1/12
s
INTERNALLY FREQUENCY COMPENSATED
s
LARGE DC VOLTAGE GAIN: 100dB
s
WIDE BANDWIDTH (unity gain): 1.1MHz
(temperature compensated)
s
VERY LOW SUPPLY CURRENT/OP (500A)
ESSENTIALLY INDEPENDENT OF SUPPLY
VOLTAGE
s
LOW INPUT BIAS CURRENT: 20nA
(temperature compensated)
s
LOW INPUT OFFSET VOLTAGE: 2mV
s
LOW INPUT OFFSET CURRENT: 2nA
s
INPUT COMMON-MODE VOLTAGE RANGE
INCLUDES GROUND
s
DIFFERENTIAL INPUT VOLTAGE RANGE
EQUAL TO THE POWER SUPPLY VOLTAGE
s
LARGE OUTPUT VOLTAGE SWING 0V TO
(Vcc - 1.5V)
DESCRIPTION
These circuits consist of two independent, high
gain, internally frequency compensated which
were designed specifically to operate from a sin-
gle power supply over a wide range of voltages.
The low power supply drain is independent of the
magnitude of the power supply voltage.
Application areas include transducer amplifiers,
dc gain blocks and all the conventional op-amp
circuits which now can be more easily implement-
ed in single power supply systems. For example,
these circuits can be directly supplied with the
standard +5V which is used in logic systems and
will easily provide the required interface electron-
ics without requiring any additional power supply.
Inthe linear mode the input common-mode voltage
range includes ground and the output voltage can
also swing to ground, even though operated from
only a single power supply voltage.
ORDER CODE
N = Dual in Line Package (DIP)
D = Small Outline Package (SO) - also available in Tape & Reel (DT)
S = Small Outline Package (miniSO) only available in Tape & Reel (DT)
P = Thin Shrink Small Outline Package (TSSOP) - only available in Tape
&Reel (PT)
PIN CONNECTIONS (top view)
Part
Number
Temperature
Range
Package
N
S
D
P
LM158,A
-55C, +125C
LM258,A
-40C, +105C
LM358,A
0C, +70C
Example : LM258N
N
DIP8
(Plastic Package)
D & S
SO8 & miniSO8
(Plastic Micropackage)
P
TSSOP8
(Thin Shrink Small Outline Package)
1 - Output 1
2 - Inverting input
3 - Non-inverting input
4 - V
CC
-
5 - Non-inverting input 2
6 - Inverting input 2
7 - Output 2
8 - V
CC
+
1
2
3
4
5
6
7
8
-
+
-
+
LM158,A-LM258,A
LM358,A
LOW POWER DUAL OPERATIONAL AMPLIFIERS
July 2003
LM158,A-LM258,A-LM358,A
2/12
SCHEMATIC DIAGRAM (1/2 LM158)
ABSOLUTE MAXIMUM RATINGS
Symbol
Parameter
LM158,A
LM258,A
LM358,A
Unit
V
CC
Supply voltage
+/-16 or 32
V
V
i
Input Voltage
-0.3 to +32
V
V
id
Differential Input Voltage
+32
V
P
tot
Power Dissipation
1)
1.
Power dissipation must be considered to ensure maximum junction temperature (Tj) is not exceeded.
500
mW
Output Short-circuit Duration
2)
2.
Short-circuits from the output to V
CC
can cause excessive heating if V
CC
> 15V. The maximum output current is approximately 40mA independent
of the magnitude of V
CC
. Destructive dissipation can result from simultaneous short-circuit on all amplifiers.
Infinite
I
in
Input Current
3)
3.
This input current only exists when the voltage at any of the input leads is driven negative. It is due to the collector-base junction of the input PNP
transistor becoming forward biased and thereby acting as input diodes clamps. In addition to this diode action, there is also NPN parasitic action on
the IC chip. this transistor action can cause the output voltages of the Op-amps to go to the V
CC
voltage level (or to ground for a large overdrive)
for the time duration than an input is driven negative.
This is not destructive and normal output will set up again for input voltage higher than -0.3V.
50
mA
T
oper
Opearting Free-air Temperature Range
-55 to +125
-40 to +105
0 to +70
C
T
stg
Storage Temperature Range
-65 to +150
C
6
A
4
A
100
A
Q2
Q3
Q4
Q1
Inverting
input
Non-inverting
input
Q8
Q9
Q10
Q11
Q12
50
A
Q13
Output
Q7
Q6
Q5
R
SC
V
CC
C
C
GND
LM158,A-LM258,A-LM358,A
3/12
ELECTRICAL CHARACTERISTICS
V
CC
+
= +5V, V
CC
-
= Ground, V
o
= 1.4V, T
amb
= +25C (unless otherwise specified)
Symbol
Parameter
LM158A-LM258A
LM358A
LM158-LM258
LM358
Unit
Min.
Typ.
Max.
Min.
Typ.
Max.
V
io
Input Offset Voltage - note
1)
T
amb
= +25C
LM158, LM258
LM158A
T
min
T
amb
T
max
LM158, LM258
1
3
2
4
2
7
5
9
7
mV
I
io
Input Offset Current
T
amb
= +25C
T
min
T
amb
T
max
2
10
30
2
30
40
nA
I
ib
Input Bias Current - note
2)
T
amb
= +25C
T
min
T
amb
T
max
20
50
100
20
150
200
nA
A
vd
Large Signal Voltage Gain
V
CC
= +15V, R
L
= 2k
,
V
o
= 1.4V to 11.4V
T
amb
= +25C
T
min
T
amb
T
max
50
25
100
50
25
100
V/mV
SVR
Supply Voltage Rejection Ratio (R
s
10k
)
V
CC
+
= 5V to 30V
T
amb
= +25C
T
min
T
amb
T
max
65
65
100
65
65
100
dB
I
CC
Supply Current, all Amp, no load
T
min
T
amb
T
max
V
CC
= +5V
T
min
T
amb
T
max
V
CC
= +30V
0.7
1.2
1
0.7
1.2
2
mA
V
icm
Input Common Mode Voltage Range
V
CC
= +30V - note
3)
T
amb
= +25C
T
min
T
amb
T
max
0
0
V
CC
+
-1.5
V
CC
+
-2
0
0
V
CC
+
-1.5
V
CC
+
-2
V
CMR
Common Mode Rejection Ratio (R
s
10k
)
T
amb
= +25C
T
min
T
amb
T
max
70
60
85
70
60
85
dB
I
source
Output Current Source
V
CC
= +15V, V
o
= +2V, V
id
= +1V
20
40
60
20
40
60
mA
I
sink
Output Sink Current (V
id
= -1V)
V
CC
= +15V, V
o
= +2V
V
CC
= +15V, V
o
= +0.2V
10
12
20
50
10
12
20
50
mA
A
V
OPP
Output Voltage Swing ( R
L
= 2k
)
T
amb
= +25C
T
min
T
amb
T
max
0
0
V
CC
+
-1.5
V
CC
+
-2
0
0
V
CC
+
-1.5
V
CC
+
-2
LM158,A-LM258,A-LM358,A
4/12
V
OH
High Level Output Voltage (V
CC
+
= 30V)
T
amb
= +25C
R
L
= 2k
T
min
T
amb
T
max
T
amb
= +25C
R
L
= 10k
T
min
T
amb
T
max
26
26
27
27
27
28
26
26
27
27
27
28
V
V
OL
Low Level Output Voltage (R
L
= 10k
)
T
amb
= +25C
T
min
T
amb
T
max
5
20
20
5
20
20
mV
SR
Slew Rate
V
CC
= 15V, V
i
= 0.5 to 3V, R
L
= 2k
,
C
L
= 100pF, unity Gain
0.3
0.6
0.3
0.6
V/
s
GBP
Gain Bandwidth Product
V
CC
= 30V, f =100kHz,V
in
= 10mV, R
L
= 2k
,
C
L
= 100pF
0.7
1.1
0.7
1.1
MHz
THD
Total Harmonic Distortion
f = 1kHz, A
v
= 20dB, R
L
= 2k
,
V
o
= 2V
pp
,
C
L
= 100pF, V
O
= 2Vpp
0.02
0.02
%
e
n
Equivalent Input Noise Voltage
f = 1kHz, R
s
= 100
,
V
CC
= 30V
55
55
DV
io
Input Offset Voltage Drift
7
15
7
30
V/C
DI
Iio
Input Offset Current Drift
10
200
10
300
pA/C
V
o1
/V
o2
Channel Separation - note
4)
1kHz
f
20kHZ
120
120
dB
1.
V
o
= 1.4V, R
s
= 0
, 5V < V
CC
+
< 30V, 0 < V
ic
< V
CC
+
- 1.5V
2.
The direction of the input current is out of the IC. This current is essentially constant, independent of the state of the output so no loading change
exists on the input lines.
3.
The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V. The upper end of the
common-mode voltage range is V
CC
+
- 1.5V, but either or both inputs can go to +32V without damage.
4.
Due to the proximity of external components insure that coupling is not originating via stray capacitance between these external parts. This typically
can be detected as this type of capacitance increases at higher frequences.
Symbol
Parameter
LM158A-LM258A
LM358A
LM158-LM258
LM358
Unit
Min.
Typ.
Max.
Min.
Typ.
Max.
nV
Hz
------------
VOLTAGE GAIN (dB)
OPEN LOOP FREQUENCY RESPONSE
(NOTE 3)
1.0
10 100 1k
10k 100k 1M 10M
VCC = +10 to + 15V &
FREQUENCY (Hz)
10M
W
VI
VCC/2
VCC = 30V &
0.1
m
F
VCC
VO
-
+
-55C Tamb +125C
140
120
100
80
60
40
20
0
-55C Tamb +125C
LARGE SIGNAL FREQUENCY RESPONSE
FREQUENCY (Hz)
1k 10k 100k 1M
OUTPUT SWING (Vpp)
+7V
2k
W
1k
W
100k
W
+15V
VO
-
+
VI
20
15
10
5
0
LM158,A-LM258,A-LM358,A
5/12
INPUT
VOLTAGE (V)
OUTPUT
VOLTAGE (V)
VOLAGE FOLLOWER PULSE RESPONSE
0
10
20
30
40
TIME (
m
s)
RL 2 k
W
VCC = +15V
4
3
2
1
0
3
2
1
OUTPUT VOLTAGE (mV)
VOLTAGE FOLLOWER PULSSE RESPONSE
(SMALL SIGNAL)
0 1 2 3 4 5 6 7 8
Input
Tamb = +25C
VCC = 30 V
Output
eO
el
50pF
+
-
TIME (
m
s)
500
450
400
350
300
250
INPUT CURRENT (mA)
INPUT CURRENT (Note 1)
-55 -35 -15
5
25
45 65
85 105 125
VI = 0 V
VCC = +30 V
VCC = +15 V
VCC = +5 V
TEMPERATURE (C)
90
80
70
60
50
40
30
20
10
0
OUTPUT CHARACTERISTICS
OUTPUT SINK CURRENT (mA)
0,001 0,01 0,1 1 10 100
OUTPUT VOLTAGE (V)
VCC = +5V
VCC = +15V
VCC = +30V
-
IO
VO
Tamb = +25C
vcc/2
vcc
+
10
1
0.1
0.01
OUTPUT VOLTAGE REFERENCED
TO V
CC
+ (V)
OUTPUT CHARACTERISTICS
0,01
0,1
1
10 100
0,001
Independent of VCC
Tamb = +25C
+
-
VCC
VO
IO
VCC /2
OUTPUT SOURCE CURRENT (mA)
8
7
6
5
4
3
2
1
OUTPUT CURRENT (mA)
CURRENT LIMITING (Note 1)
-
+
IO
TEMPERATURE (C)
90
80
70
60
50
40
30
20
10
0
-55 -35 -15
5
25
45 65
85 105 125
LM158,A-LM258,A-LM358,A
6/12
INPUT VOLTAGE (V)
INPUT VOLTAGE RANGE
0
5
10
15
POWER SUPPLY VOLTAGE (V)
Ngative
Positive
15
10
5
0 10 20 30 40
POSITIVE SUPPLY VOLTAGE (V)
VOLTAGE GAIN (dB)
160
120
80
40
L
R = 20k
W
L
R = 2k
W
0 10 20 30
POSITIVE SUPPLY VOLTAGE (V)
VOLTAGE GAIN (dB)
160
120
80
40
L
R = 20k
W
L
R = 2k
W
SUPPLY CURRENT (mA)
SUPPLY CURRENT
0
10
20
30
Tamb = -55C
VCC
mA
ID
-
+
Tamb = 0C to +125C
POSITIVE SUPPLY VOLTAGE (V)
4
3
2
1
0 10 20 30
POSITIVE SUPPLY VOLTAGE (V)
INPUT CURRENT (nA)
100
75
50
25
amb
T = +25C
-55-35-15 5 25 45 65 85 105 125
TEMPERATURE (C)
GAIN BANDWIDTH PRODUCT (MHz)
CC
V = 15V
1.5
1.35
1.2
1.05
0.9
0.75
0.6
0.45
0.3
0.15
0
LM158,A-LM258,A-LM358,A
7/12
TYPICAL APPLICATIONS (single supply voltage) V
cc
= +5V
dc
AC COUPLED INVERTING AMPLIFIER
NON-INVERTING DC AMPLIFIER
AC COUPLED NON-INVERTING AMPLIFIER
DC SUMMING AMPLIFIER
-55-35-15 5 25 45 65 85 105 125
TEMPERATURE (C)
POWER SUPPLY REJECTION RATIO (dB)
SVR
115
110
105
100
95
90
85
80
75
70
65
60
-55-35-15 5 25 45 65 85 105 125
TEMPERATURE (C)
COMMON MODE REJECTION RATIO (dB)
115
110
105
100
95
90
85
80
75
70
65
60
1/2
LM158
~
0
2V
PP
R
10k
W
L
C
o
e
o
R
6.2k
W
B
R
100k
W
f
R1
10k
W
C
I
e
I
V
CC
R2
100k
W
C1
10
m
F
R3
100k
W
A = -
R
R1
V
f
(as shown A
= -10)
V
R1
10k
W
R2
1M
W
1/2
LM158
10k
W
e
I
e
O
+5V
e
O
(V
)
(mV)
0
A
V
= 1 +
R2
R1
(As shown
= 101)
A
V
1/2
LM158
~
0
2V
PP
R
10k
W
L
C
o
e
o
R
6.2k
W
B
C1
0.1
m
F
e
I
V
CC
(as shown A
= 11)
V
A = 1 + R2
R1
V
R1
100k
W
R2
1M
W
C
I
R3
1M
W
R4
100k
W
R5
100k
W
C2
10
m
F
1/2
LM158
e
O
e
4
e
3
e
2
e
1
100k
W
100k
W
100k
W
100k
W
100k
W
100k
W
e
o
= e
1
+ e
2
- e
3
- e
4
where (e1 + e
2
)
(e
3
+ e
4
)
to keep e
o
0V
LM158,A-LM258,A-LM358,A
8/12
HIGH INPUT Z, DC DIFFERENTIAL AMPLIFIER
HIGH INPUT Z ADJUSTABLE GAIN DC
INSTRUMENTATION AMPLIFIER
USING SYMMETRICAL AMPLIFIERS TO
REDUCE INPUT CURRENT
LOW DRIFT PEAK DETECTOR
ACTIVE BAND-PASS FILTER
R1
100k
W
R2
100k
W
R4
100k
W
R3
100k
W
+V2
+V1
V
o
1/2
LM158
1/2
LM158
if R1 = R5 and R3 = R4 = R6 = R7
e
o
= [ 1 + ] ( (e
2
+ e
1
)
As shown e
o
= 101 (e
2
+ e
1
)
2
R1
R2
-----------
R3
100k
W
e
O
1/2
LM158
R1
100k
W
e
1
R7
100k
W
R6
100k
W
R5
100k
W
e
2
R2
2k
W
Gain adjust
R4
100k
W
1/2
LM158
1/2
LM158
if R1 = R5 and R3 = R4 = R6 = R7
e
o
= [ 1 + ] ( (e
2
+ e
1
)
As shown e
o
= 101 (e
2
+ e
1
)
2
R1
R2
-----------
1/2
LM158
I
B
2N 929
0.001
m
F
I
B
3M
W
I
B
e
o
I
I
e
I
I
B
I
B
Input current compensation
1.5M
W
1/2
LM158
I
B
2N 929
0.001
m
F
I
B
3R
3M
W
I
B
Input current
compensation
e
o
I
B
e
I
1/2
LM158
Z
o
Z
I
C
1
m
F
2I
B
R
1M
W
2I
B
1/2
LM158
1/2
LM158
1/2
LM158
R8
100k
W
C3
10
m
F
R7
100k
W
R5
470k
W
C1
330pF
V
o
V
CC
R6
470k
W
C2
330pF
R4
10M
W
R1
100k
W
R2
100k
W
+V1
R3
100k
W
1/2
LM158
1/2
LM158
LM158,A-LM258,A-LM358,A
9/12
PACKAGE MECHANICAL DATA
8 PINS - PLASTIC DIP
Dim.
Millimeters
Inches
Min.
Typ.
Max.
Min.
Typ.
Max.
A
3.32
0.131
a1
0.51
0.020
B
1.15
1.65
0.045
0.065
b
0.356
0.55
0.014
0.022
b1
0.204
0.304
0.008
0.012
D
10.92
0.430
E
7.95
9.75
0.313
0.384
e
2.54
0.100
e3
7.62
0.300
e4
7.62
0.300
F
6.6
0260
i
5.08
0.200
L
3.18
3.81
0.125
0.150
Z
1.52
0.060
LM158,A-LM258,A-LM358,A
10/12
PACKAGE MECHANICAL DATA
8 PINS - PLASTIC MICROPACKAGE ( miniSO )
Dim.
Millimeters
Inches
Min.
Typ.
Max.
Min.
Typ.
Max.
A
1.100
0.043
A1
0.050
0.100
0.150
0.002
0.004
0.006
A2
0.780
0.860
0.940
0.031
0.034
0.037
b
0.250
0.330
0.400
0.010
0.013
0.016
c
0.130
0.180
0.230
0.005
0.007
0.009
D
2.900
3.000
3.100
0.114
0.118
0.122
E
4.750
4.900
5.050
0.187
0.193
0.199
E1
2.900
3.000
3.100
0.114
0.118
0.122
e
0.650
0.026
L
0.400
0.550
0.700
0.016
0.022
0.028
L1
0.950
0.037
k
0d
3d
6d
0d
3d
6d
ccc
0.100
0.004
0,25 mm
.010 inch
GAGE PLANE
C
ccc
C
PLANE
SEA
TING
E
A
A2
A1
D
b
e
E1
L
k
c
1
4
8
5
PIN 1 IDENTIFICATION
L1
LM158,A-LM258,A-LM358,A
11/12
PACKAGE MECHANICAL DATA
8 PINS - PLASTIC MICROPACKAGE (SO)
Dim.
Millimeters
Inches
Min.
Typ.
Max.
Min.
Typ.
Max.
A
1.75
0.069
a1
0.1
0.25
0.004
0.010
a2
1.65
0.065
a3
0.65
0.85
0.026
0.033
b
0.35
0.48
0.014
0.019
b1
0.19
0.25
0.007
0.010
C
0.25
0.5
0.010
0.020
c1
45 (typ.)
D
4.8
5.0
0.189
0.197
E
5.8
6.2
0.228
0.244
e
1.27
0.050
e3
3.81
0.150
F
3.8
4.0
0.150
0.157
L
0.4
1.27
0.016
0.050
M
0.6
0.024
S
8 (max.)
b
e3
A
a2
s
L
C
E
c1
a3
b1
a1
D
M
8
5
1
4
F
LM158,A-LM258,A-LM358,A
12/12
PACKAGE MECHANICAL DATA
8 PINS - THIN SHRINK SMALL OUTLINE PACKAGE (TSSOP)
Dim.
Millimeters
Inches
Min.
Typ.
Max.
Min.
Typ.
Max.
A
1.20
0.05
A1
0.05
0.15
0.01
0.006
A2
0.80
1.00
1.05
0.031
0.039
0.041
b
0.19
0.30
0.007
0.15
c
0.09
0.20
0.003
0.012
D
2.90
3.00
3.10
0.114
0.118
0.122
E
6.40
0.252
E1
4.30
4.40
4.50
0.169
0.173
0.177
e
0.65
0.025
k
0
8
0
8
l
0.50
0.60
0.75
0.09
0.0236
0.030
L
0.45
0.600
0.75
0.018
0.024
0.030
L1
1.000
0.039
C
L
14
8
5
L1
c
0.25mm
.010 inch
GAGE PLANE
E1
k
L
L1
E
SEA
TING
PLANE
A
A2
D
A1
b
5
8
4
1
PIN 1 IDENTIFICATION
e
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the
consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from
its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications
mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information
previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or
systems without express written approval of STMicroelectronics.
The ST logo is a registered trademark of STMicroelectronics
2003 STMicroelectronics - All Rights Reserved
STMicroelectronics GROUP OF COMPANIES
Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco
Singapore - Spain - Sweden - Switzerland - United Kingdom
http://www.st.com
PDF 
ZIP