1996 Microchip Technology Inc.
DS21053E-page 1
FEATURES
Single supply with operation down to 1.8V
Low power CMOS technology
- 1 mA active current typical
- 10
A standby current typical at 5.5V
- 3
A standby current typical at 1.8V
Organized as 2 or 4 blocks of 256 bytes
(2 x 256 x 8) or (4 x 256 x 8)
2-wire serial interface bus, I
2
C
TM
compatible
Schmitt trigger, filtered inputs for noise suppres-
sion
Output slope control to eliminate ground bounce
100 kHz (1.8V) and 400 kHz (5V) compatibility
Self-timed write cycle (including auto-erase)
Page-write buffer for up to 16 bytes
2 ms typical write cycle time for page-write
Hardware write protect for entire memory
Can be operated as a serial ROM
ESD protection > 4,000V
1,000,000 ERASE/WRITE cycles guaranteed
Data retention > 200 years
8-pin DIP, 8-lead or 14-lead SOIC packages
Available for extended temperature ranges
DESCRIPTION
The Microchip Technology Inc. 24AA04/08 is a 4K bit or
8K bit Electrically Erasable PROM. The device is orga-
nized as two or four blocks of 256 x 8-bit memory with
a two wire serial interface. Low voltage design permits
operation down to 1.8 volts with standby and active cur-
rents of only 3
A and 1 mA respectively. The 24AA04/
08 also has a page-write capability for up to 16 bytes of
data. The 24AA04/08 is available in the standard 8-pin
DIP and both 8-lead and 14-lead surface mount SOIC
packages.
- Commercial (C):
0
C to +70
C
- Industrial (I):
-40
C to +85
C
PACKAGE TYPES
BLOCK DIAGRAM
NC
SS
CC
A0
A1
NC
A2
NC
V
1
2
3
4
5
6
7
14
13
12
NC
SCL
SDA
NC
9
8
11
10
WP
V
NC
24AA04/08
14-Lead
SOIC
24AA04/08
A0
A1
A2
V
SS
1
2
3
4
8
7
6
5
V
CC
WP
SCL
SDA
24AA04/08
A0
A1
A2
V
SS
1
2
3
4
8
7
6
5
V
CC
WP
SCL
SDA
DIP
8-lead
SOIC
HV GENERATOR
EEPROM
ARRAY
PAGE LATCHES
YDEC
XDEC
SENSE AMP
R/W CONTROL
MEMORY
CONTROL
LOGIC
I/O
CONTROL
LOGIC
WP
SDA
SCL
V
CC
V
SS
24AA04/08
4K/8K 1.8V I
2
C
TM
Serial EEPROMs
I
2
C is a trademark of Philips Corporation.
This document was created with FrameMaker 4 0 4
24AA04/08
DS21053E-page 2
1996 Microchip Technology Inc.
1.0
ELECTRICAL
CHARACTERISTICS
1.1
Maximum Ratings*
V
CC
...................................................................................7.0V
All inputs and outputs w.r.t. V
SS
.............. -0.6V to VCC +1.0V
Storage temperature ..................................... -65C to +150C
Ambient temp. with power applied ................ -65C to +125C
Soldering temperature of leads (10 seconds) ............. +300C
ESD protection on all pins
..................................................
4 kV
*Notice:
Stresses above those listed under "Maximum ratings"
may cause permanent damage to the device. This is a stress rat-
ing only and functional operation of the device at those or any
other conditions above those indicated in the operational listings
of this specification is not implied. Exposure to maximum rating
conditions for extended periods may affect device reliability.
TABLE 1-1:
PIN FUNCTION TABLE
Name
Function
V
SS
Ground
SDA
Serial Address/Data I/O
SCL
Serial Clock
WP
Write Protect Input
Vcc
+1.8V to 5.5V Power Supply
A0, A1, A2
No Internal Connection
TABLE 1-2:
DC CHARACTERISTICS
FIGURE 1-1:
BUS TIMING START/STOP
V
CC
= +1.8V to +5.5V
Commercial (C): Tamb = 0C to +70C
Industrial (I): Tamb = -40
C to +85
C
Parameter
Sym
Min
Typ
Max
Units
Conditions
WP, SCL and SDA pins:
High level input voltage
V
IH
.7 Vcc
--
--
V
Low Level input voltage
V
IL
--
--
.3 V
CC
V
Hysteresis of Schmitt trigger
inputs
V
HYS
.05 V
CC
--
--
V
(Note)
Low level output voltage
V
OL
--
--
.40
V
I
OL
= 3.0 mA, V
CC
= 1.8V
Input leakage current
I
LI
-10
--
10
A
V
IN
= .1V to V
CC
Output leakage current
I
LO
-10
--
10
A
V
OUT
= .1V to V
CC
Pin capacitance
(all inputs/outputs)
C
IN
, C
OUT
--
--
10
pF
V
CC
= 5.0V (Note 1)
Tamb = 25C, F
CLK
= 1 MHz
Operating current
I
CC
W
RITE
I
CC
R
EAD
--
--
--
--
--
0.5
--
0.05
3
--
1
--
mA
mA
mA
mA
V
CC
= 5.5V, SCL = 400 kHz
V
CC
= 1.8V, SCL = 100 kHz
V
CC
= 5.5V, SCL = 400 kHz
V
CC
= 1.8V, SCL = 100 kHz
Standby current
I
CCS
--
--
--
3
100
30
--
A
A
A
V
CC
= 5.5V, SDA=SCL=V
CC
V
CC
= 3.0V, SDA=SCL=V
CC
V
CC
= 1.8V, SDA=SCL=V
CC
Note:This parameter is periodically sampled and not 100% tested.
T
SU
:
STA
T
HD
:
STA
V
HYS
T
SU
:
STO
START
STOP
SCL
SDA
1996 Microchip Technology Inc.
DS21053E-page 3
24AA04/08
TABLE 1-3:
AC CHARACTERISTICS
FIGURE 1-2:
BUS TIMING DATA
Parameter
Symbol
Standard Mode
V
CC
= 4.5-5.5V
Fast Mode
Units
Remarks
Min
Max
Min
Max
Clock frequency
Fclk
--
100
--
400
kHz
Clock high time
Thigh
4000
--
600
--
ns
Clock low time
Tlow
4700
--
1300
--
ns
SDA and SCL rise time
Tr
--
1000
--
300
ns
(Note 1)
SDA and SCL fall time
Tf
--
300
--
300
ns
(Note 1)
START condition hold time
T
HD
:
STA
4000
--
600
--
ns
After this period the first clock
pulse is generated
START condition setup
time
T
SU
:
STA
4700
--
600
--
ns
Only relevant for repeated
START condition
Data input hold time
T
HD
:
DAT
0
--
0
--
ns
Data input setup time
T
SU
:
DAT
250
--
100
--
ns
STOP condition setup time T
SU
:
STO
4000
--
600
--
ns
Output valid from clock
T
AA
--
3500
--
900
ns
(Note 2)
Bus free time
T
BUF
4700
--
1300
--
ns
Time the bus must be free before
a new transmission can start
Output fall time from V
IH
min to V
IL
max
T
OF
--
250
20 + 0.1
C
B
250
ns
(Note 1), C
B
100 pF
Input filter spike suppres-
sion (SDA and SCL pins)
T
SP
--
50
--
50
ns
(Note 3)
Write cycle time
T
WR
--
10
--
10
ms
Byte or Page mode
Endurance
24AA04
24AA08
--
10M
1M
--
10M
1M
--
cycles 25
C, Vcc = 5.0V, Block Mode
(Note 4)
Note 1: Not 100% tested. C
B
= total capacitance of one bus line in pF.
2: As a transmitter, the device must provide an internal minimum delay time to bridge the undefined region (min-
imum 300 ns) of the falling edge of SCL to avoid unintended generation of START or STOP conditions.
3: The combined T
SP
and V
HYS
specifications are due to new Schmitt trigger inputs which provide improved
noise and spike suppression. This eliminates the need for a T
I
specification for standard operation.
4: This parameter is not tested but guaranteed by characterization. For endurance estimates in a specific appli-
cation, please consult the Total Endurance Model which can be obtained on our BBS or website.
T
SU
:
STA
T
F
T
LOW
T
HIGH
T
R
T
HD
:
DAT
T
SU
:
DAT
T
SU
:
STO
T
HD
:
STA
T
BUF
T
AA
T
AA
T
SP
T
HD
:
STA
SCL
SCL
IN
SCL
OUT
This document was created with FrameMaker 4 0 4
24AA04/08
DS21053E-page 4
1996 Microchip Technology Inc.
2.0
FUNCTIONAL DESCRIPTION
The 24AA04/08 supports a Bi-directional 2-wire bus
and data transmission protocol. A device that sends
data onto the bus is defined as transmitter, and a device
receiving data as receiver. The bus has to be controlled
by a master device which generates the serial clock
(SCL), controls the bus access, and generates the
START and STOP conditions, while the 24AA04/08
works as slave. Both master and slave can operate as
transmitter or receiver, but the master device deter-
mines which mode is activated.
3.0
BUS CHARACTERISTICS
The following
bus protocol
has been defined:
Data transfer may be initiated only when the bus is
not busy.
During data transfer, the data line must remain
stable whenever the clock line is HIGH. Changes
in the data line while the clock line is HIGH will be
interpreted as a START or STOP condition.
Accordingly, the following bus conditions have been
defined (Figure 3-1).
3.1
Bus not Busy (A)
Both data and clock lines remain HIGH.
3.2
Start Data Transfer (B)
A HIGH to LOW transition of the SDA line while the
clock (SCL) is HIGH determines a START condition. All
commands must be preceded by a START condition.
3.3
Stop Data Transfer (C)
A LOW to HIGH transition of the SDA line while the
clock (SCL) is HIGH determines a STOP condition. All
operations must be ended with a STOP condition.
3.4
Data Valid (D)
The state of the data line represents valid data when,
after a START condition, the data line is stable for the
duration of the HIGH period of the clock signal.
The data on the line must be changed during the LOW
period of the clock signal. There is one clock pulse per
bit of data.
Each data transfer is initiated with a START condition
and terminated with a STOP condition. The number of
the data bytes transferred between the START and
STOP conditions is determined by the master device
and is theoretically unlimited, although only the last six-
teen will be stored when doing a write operation. When
an overwrite does occur it will replace data in a first in
first out fashion.
3.5
Acknowledge
Each receiving device, when addressed, is obliged to
generate an acknowledge after the reception of each
byte. The master device must generate an extra clock
pulse which is associated with this acknowledge bit.
The device that acknowledges, has to pull down the
SDA line during the acknowledge clock pulse in such a
way that the SDA line is stable LOW during the HIGH
period of the acknowledge related clock pulse. Of
course, setup and hold times must be taken into
account. A master must signal an end of data to the
slave by not generating an acknowledge bit on the last
byte that has been clocked out of the slave. In this
case, the slave must leave the data line HIGH to enable
the master to generate the STOP condition.
Note:
The 24AA04/08 does not generate any
acknowledge bits if an internal program-
ming cycle is in progress.
FIGURE 3-1:
DATA TRANSFER SEQUENCE ON THE SERIAL BUS
(A)
(B)
(D)
(D)
(A)
(C)
SCL
SDA
START
CONDITION
ADDRESS OR
ACKNOWLEDGE
VALID
DATA
ALLOWED
TO CHANGE
STOP
CONDITION
1996 Microchip Technology Inc.
DS21053E-page 5
24AA04/08
3.6
Device Addressing
A control byte is the first byte received following the
start condition from the master device. The control byte
consists of a four bit control code, for the 24AA04/08
this is set as 1010 binary for read and write operations.
The next three bits of the control byte are the block
select bits (B2, B1, B0). B2 is a don't care for both the
24AA04 and 24AA08; B1 is a don't care for the 24AA04.
They are used by the master device to select which of
the two or four 256 word blocks of memory are to be
accessed. These bits are in effect the most significant
bits of the word address.
The last bit of the control byte defines the operation to
be performed. When set to one a read operation is
selected, when set to zero a write operation is selected.
Following the start condition, the 24AA04/08 monitors
the SDA bus checking the device type identifier being
transmitted, upon a 1010 code the slave device outputs
an acknowledge signal on the SDA line. Depending on
the state of the R/W bit, the 24AA04/08 will select a
read or write operation.
FIGURE 3-2:
CONTROL BYTE
ALLOCATION
Operation
Control
Code
Block Select
R/W
Read
1010
Block Address
1
Write
1010
Block Address
0
START
READ/WRITE
SLAVE ADDRESS
R/W
1
0
1
0
X
B1
B0
A
X = don't care, B1 is don't care for 24AA04
4.0
WRITE OPERATION
4.1
Byte Write
Following the start condition from the master, the
device code (4 bits), the block address (3 bits), and the
R/W bit which is a logic low is placed onto the bus by
the master transmitter. This indicates to the addressed
slave receiver that a byte with a word address will follow
after it has generated an acknowledge bit during the
ninth clock cycle. Therefore the next byte transmitted by
the master is the word address and will be written into
the address pointer of the 24AA04/08. After receiving
another acknowledge signal from the 24AA04/08 the
master device will transmit the data word to be written
into the addressed memory location. The 24AA04/08
acknowledges again and the master generates a stop
condition. This initiates the internal write cycle, and dur-
ing this time the 24AA04/08 will not generate acknowl-
edge signals (Figure 4-1).
4.2
Page Write
The write control byte, word address, and the first data
byte are transmitted to the 24AA04/08 in the same way
as in a byte write. But instead of generating a stop con-
dition, the master transmits up to 16 data bytes to the
24AA04/08 which are temporarily stored in the on-chip
page buffer and will be written into the memory after the
master has transmitted a stop condition. After the
receipt of each word, the four lower order address
pointer bits are internally incremented by one. The
higher order seven bits of the word address remains
constant. If the master should transmit more than 16
words prior to generating the stop condition, the
address counter will roll over and the previously
received data will be overwritten. As with the byte write
operation, once the stop condition is received an inter-
nal write cycle will begin (Figure 4-2).
FIGURE 4-1:
BYTE WRITE
FIGURE 4-2:
PAGE WRITE
S
P
BUS ACTIVITY
MASTER
SDA LINE
BUS ACTIVITY
S
T
A
R
T
S
T
O
P
CONTROL
BYTE
WORD
ADDRESS
DATA
A
C
K
A
C
K
A
C
K
S
P
BUS ACTIVITY
MASTER
SDA LINE
BUS ACTIVITY
S
T
A
R
T
CONTROL
BYTE
WORD
ADDRESS (n)
DATA n
DATA n + 15
S
T
O
P
A
C
K
A
C
K
A
C
K
A
C
K
A
C
K
DATA n + 1
PDF 
ZIP