Document Outline
- FEATURES
- APPLICATIONS
- GENERAL DESCRIPTION
- FUNCTIONAL BLOCK DIAGRAM
-
-
-
-
-
-
-
-
-
-
Active Receive Mixer
LF to 500 MHz
AD8342
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
2005 Analog Devices, Inc. All rights reserved.
FEATURES
Broadband RF port: LF to 500 MHz
Conversion gain: 3.7 dB
Noise figure: 12.2 dB
Input IP3: 22.7 dBm
Input P
1dB
: 8.3 dBm
LO drive: 0 dBm
Differential high impedance RF input port
Single-ended, 50 LO input port
Single-supply operation: 5 V @ 98 mA
Power-down mode
Exposed paddle LFCSP: 3 mm 3 mm
APPLICATIONS
Cellular base station receivers
ISM receivers
Radio links
RF instrumentation
FUNCTIONAL BLOCK DIAGRAM
8
7
6
13
15
16
COMM
IFOP
IFOM
5
COMM
14
2
1
3
4
COMM
RFCM
RFIN
VPMX
VPDC PWDN
EXRB COMM
11
12
10
9
VPLO LOCM
LOIN
COMM
BIAS
AD8342
05352-001
Figure 1.
GENERAL DESCRIPTION
The AD8342 is a high performance, broadband active mixer.
It is well suited for demanding receive-channel applications
that require wide bandwidth on all ports and very low inter-
modulation distortion and noise figure.
The AD8342 provides a typical conversion gain of 3.7 dB with
an RF frequency of 238 MHz. The integrated LO driver presents
a 50 input impedance with a low LO drive level, helping to
minimize the external component count.
The differential high impedance broadband RF port allows for
easy interfacing to both active devices and passive filters. The
RF input accepts input signals as large as 1.6 V p-p or 8 dBm
(relative to 50 ) at P
1dB
.
The open-collector differential outputs provide excellent bal-
ance and can be used with a differential filter or IF amplifier,
such as the AD8369 or AD8351. These outputs can also be con-
verted to a single-ended signal through the use of a matching
network or a transformer (balun). When centered on the VPOS
supply voltage, the outputs may swing 2 V differentially.
The AD8342 is fabricated on an Analog Devices proprietary,
high performance SiGe IC process. The AD8342 is available in a
16-lead LFCSP. It operates over a -40C to +85C temperature
range. An evaluation board is also available.
AD8342
Rev. 0 | Page 2 of 20
TABLE OF CONTENTS
Specifications..................................................................................... 3
AC Performance ............................................................................... 4
Spur Table .......................................................................................... 5
Absolute Maximum Ratings............................................................ 6
ESD Caution.................................................................................. 6
Pin Configuration and Function Descriptions............................. 7
Typical Performance Characteristics ............................................. 8
Circuit Description......................................................................... 14
AC Interfaces................................................................................... 15
IF Port .......................................................................................... 16
LO Considerations ..................................................................... 17
High IF Applications.................................................................. 18
Evaluation Board ............................................................................ 19
Outline Dimensions ....................................................................... 20
Ordering Guide .......................................................................... 20
REVISION HISTORY
4/05--Revision 0: Initial Version
AD8342
Rev. 0 | Page 3 of 20
SPECIFICATIONS
V
S
= 5 V, T
A
= 25C, f
RF
= 238 MHz, f
LO
= 286 MHz, LO power = 0 dBm, Z
O
= 50 , R
BIAS
= 1.82 k, RF termination = 100 , IF termi-
nated into 100 through a 2:1 ratio balun, unless otherwise noted.
Table 1.
Parameter
Conditions
Min
Typ
Max
Unit
RF INPUT INTERFACE
Return Loss
Hi-Z input terminated with 100 off-chip resistor
10
dB
Input Impedance
Frequency = 238 MHz (measured at RFIN with RFCM ac-
grounded)
1||0.4
k||pF
DC Bias Level
Internally generated; port must be ac-coupled
2.4
V
OUTPUT INTERFACE
Output Impedance
Differential impedance, frequency = 48 MHz
10||0.5
k||pF
DC Bias Voltage
Supplied externally
4.75
V
S
5.25
V
Power Range
Via a 2:1 impedance ratio transformer
13
dBm
LO INTERFACE
Return Loss
10
dB
DC Bias Voltage
Internally generated; port must be ac-coupled
V
S
- 1.6
V
POWER-DOWN INTERFACE
PWDN Threshold
3.5
V
PWDN Response Time
Device enabled, IF output to 90% of its final level
0.4
s
Device disabled, supply current <5 mA
4
s
PWDN Input Bias Current
Device enabled
-80
A
Device disabled
+100
A
POWER SUPPLY
Positive Supply Voltage
4.75
5
5.25
V
Quiescent Current
VPDC
Supply current for bias cells
5
mA
VPMX, IFOP, IFOM
Supply current for mixer, R
BIAS
= 1.82 k
58
mA
VPLO
Supply current for LO limiting amplifier
35
mA
Total Quiescent Current
V
S
= 5 V
85
98
113
mA
Power-Down Current
Device disabled
500
A
AD8342
Rev. 0 | Page 4 of 20
AC PERFORMANCE
V
S
= 5 V, T
A
= 25C, LO power = 0 dBm, Z
O
= 50 , R
BIAS
= 1.82 k, RF termination 100 , IF terminated into 100 via a 2:1 ratio balun,
unless otherwise noted.
Table 2.
Parameter
Conditions
Min
Typ
Max
Unit
RF FREQUENCY RANGE
1
50
500
MHz
LO FREQUENCY RANGE
1
High side LO
60
850
MHz
IF FREQUENCY RANGE
1
10
350
MHz
CONVERSION GAIN
f
RF
= 460 MHz, f
LO
= 550 MHz, f
IF
= 90 MHz
3.2
dB
f
RF
= 238 MHz, f
LO
= 286 MHz, f
IF
= 48 MHz
3.7
dB
SSB NOISE FIGURE
f
RF
= 460 MHz, f
LO
= 550 MHz, f
IF
= 90 MHz
12.5
dB
f
RF
= 238 MHz, f
LO
= 286 MHz, f
IF
= 48 MHz
12.2
dB
INPUT THIRD-ORDER INTERCEPT
f
RF1
= 460 MHz, f
RF2
= 461 MHz, f
LO
= 550 MHz,
f
IF1
= 90 MHz, f
IF2
= 89 MHz each RF tone -10 dBm
22.2
dBm
f
RF1
= 238 MHz, f
RF2
= 239 MHz, f
LO
= 286MHz,
f
IF1
= 48MHz, f
IF2
= 47MHz each RF tone -10 dBm
22.7
dBm
INPUT SECOND-ORDER INTERCEPT f
RF1
= 460 MHz, f
RF2
= 410 MHz, f
LO
= 550 MHz, f
IF1
= 90 MHz,
f
IF2
= 140 MHz
50
dBm
f
RF1
= 238 MHz, f
RF2
= 188 MHz, f
LO
= 286 MHz, f
IF1
= 48MHz,
f
IF2
= 98 MHz
44
dBm
INPUT 1 dB COMPRESSION POINT
f
RF
= 460 MHz, f
LO
= 550 MHz, f
IF
= 90 MHz
8.5
dBm
f
RF
= 238 MHz, f
LO
= 286 MHz, f
IF
= 48 MHz
8.3
dBm
LO TO IF OUTPUT LEAKAGE
LO power = 0 dBm, f
LO
= 286 MHz
-27
dBc
LO TO RF INPUT LEAKAGE
LO power = 0 dBm, f
LO
= 286 MHz
-55
dBc
2 LO TO IF OUTPUT LEAKAGE
LO power = 0 dBm, f
RF
= 238 MHz, f
LO
= 286 MHz
IF terminated into 100 and measured with a differential probe
-47
dBm
RF TO IF OUTPUT LEAKAGE
RF power = -10 dBm, f
RF
= 238 MHz, f
LO
= 286 MHz
-32
dBc
IF/2 SPURIOUS
RF power = -10 dBm, f
RF
= 238 MHz, f
LO
= 286 MHz
-70
dBc
1
Frequency ranges are those that were extensively characterized; this device can operate over a wider range. See the H
section for details.
igh IF Applications
AD8342
Rev. 0 | Page 5 of 20
SPUR TABLE
V
S
= 5 V, T
A
= 25C, RF and LO power = 0 dBm, f
RF
= 238MHz, f
LO
= 286MHz, Z
O
= 50 , R
BIAS
= 1.82 k, RF termination 100 ,
IF terminated into 100 via a 2:1 ratio balun.
Note: Measured using standard test board. Typical noise floor of measurement system = -100 dBm.
Table 3.
m
nf
RF
- mf
LO
0 1 2 3 4 5 6 7 8 9 10
11
12
13
14
0
<-100
-25 -54 -28 -45 -35 -39 -36 -42 -57 -44 -42 -41 -46 -59
1
-39 3.5 -42 -6 -48 -16 -50 -28 -57 -37 -68 -45 -54 -37 -61
2
-52 -47 -51 -49 -54 -56 -56 -62 -62 -66 -71 -80 -80 -67 -79
3
-81 -57 -79 -61 -82 -61 -74 -69 -94 -85 -89 -86 -86 -90 -81
4
-78 -70 -80 -79 -80 -85 -87 -92 -93 -96 -95 <-100
-97 <-100
-95
5
-98 -79 -95 -87 -96 -94 -95 -88 -98 -94 <-100 <-100 <-100 <-100 <-100
6 <-100
<-100
<-100
-99
<-100
-96 <-100
<-100
<-100
<-100
<-100 <-100 <-100 <-100 <-100
7
<-100 <-100 <-100 <-100 -96
<-100 -98
<-100 <-100 <-100 <-100 <-100 <-100 <-100 <-100
8
<-100 <-100 <-100 <-100 <-100 <-100 <-100 <-100 -97
<-100 <-100 <-100 <-100 <-100 <-100
9
<-100 <-100 <-100 <-100 <-100 <-100 <-100 <-100 <-100 <-100 <-100 -99
<-100 <-100 <-100
10
<-100 <-100 <-100 <-100 <-100 <-100 <-100 <-100 <-100 <-100 -99
<-100 <-100 <-100 <-100
11
<-100 <-100 <-100 <-100 <-100 <-100 <-100 -96
<-100 -97
<-100 -96
<-100 <-100 <-100
12
<-100 <-100 <-100 <-100 <-100 <-100 <-100 <-100 -99
<-100 -98
<-100 <-100 <-100 <-100
13
<-100 <-100 <-100 <-100 <-100 <-100 <-100 <-100 <-100 -97
<-100 -97
-99
<-100 <-100
14
<-100 <-100 <-100 <-100 <-100 <-100 <-100 <-100 <-100 <-100 -98 -98 <-100
<-100
<-100
n
15
<-100 <-100 <-100 <-100 <-100 <-100 <-100 <-100 <-100 <-100 <-100 <-100 <-100 <-100 <-100
AD8342
Rev. 0 | Page 6 of 20
ABSOLUTE MAXIMUM RATINGS
Table 4.
Parameter
Rating
Supply Voltage, V
S
5.5 V
RF Input Level
12 dBm
LO Input Level
12 dBm
PWDN Pin
V
S
+ 0.5 V
IFOP, IFOM Bias Voltage
5.5 V
Minimum Resistor from EXRB to COMM
1.8 k
Internal Power Dissipation
650 mW
JA
77C/W
Maximum Junction Temperature
135C
Operating Temperature Range
-40C to +85C
Storage Temperature Range
-65C to +150C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational sec-
tion of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the
human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
AD8342
Rev. 0 | Page 7 of 20
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
05352-002
PIN 1
INDICATOR
1
VPLO
2
LOCM
3
LOIN
4
COMM
11 PWDN
12 VPDC
10 EXRB
9 COMM
5
C
O
M
M
6
I
F
O
M
7
I
F
O
P
8
C
O
M
M
1
5
R
F
I
N
1
6
V
P
M
X
1
4
R
F
C
M
1
3
C
O
M
M
TOP VIEW
(Not to Scale)
AD8342
Figure 2. 16-Lead LFCSP
Table 5. Pin Function Descriptions
Pin No.
Mnemonic
Function
1
VPLO
Positive Supply Voltage for the LO Buffer: 4.75 V to 5.25 V.
2 LOCM
AC Ground for Limiting LO Amplifier. Internally biased to Vs
- 1.6 V. AC-couple to ground.
3 LOIN
LO Input. Nominal input level 0 dBm. Input level range -10 dBm to +4 dBm (relative to 50 ). Internally
biased to Vs
- 1.6 V. AC-couple.
4, 5, 8, 9, 13
COMM
Device Common (DC Ground).
6, 7
IFOM, IFOP
Differential IF Outputs (Open Collectors). Each requires dc bias of 5.00 V (nominal).
10 EXRB
Mixer Bias Voltage. Connect resistor from EXRB to ground. Typical value of 1.82 k sets mixer current to
nominal value. Minimum resistor value from EXRB to ground = 1.8 k. Internally biased to 1.17 V.
11
PWDN
Connect to Ground for Normal Operation. Connect pin to V
S
for disable mode.
12
VPDC
Positive Supply Voltage for the DC Bias Cell: 4.75 V to 5.25 V.
14
RFCM
AC Ground for RF Input. Internally biased to 2.4 V. AC-couple to ground.
15
RFIN
RF Input. Internally biased to 2.4 V. Must be ac-coupled.
16
VPMX
Positive Supply Voltage for the Mixer: 4.75 V to 5.25 V.
AD8342
Rev. 0 | Page 8 of 20
TYPICAL PERFORMANCE CHARACTERISTICS
V
S
= 5 V, T
A
= 25C, RF power = -10 dBm, LO power = 0 dBm, Z
O
= 50 , R
BIAS
= 1.82 k, RF termination 100 , IF terminated into
100 via a 2:1 ratio balun, unless otherwise noted.
05352-004
RF FREQUENCY (MHz)
GAIN (
d
B)
IF = 10MHz
50
550
100
150
200
250
300
350
400
450
500
IF = 90MHz
6
5
4
3
2
1
IF = 48MHz
IF = 140MHz
Figure 3. Conversion Gain vs. RF Frequency
5
0
05352-025
LO LEVEL (dBm)
GAIN (
d
B)
15
10
5
0
5
IF = 48MHz
IF = 90MHz
IF = 140MHz
4
3
2
1
IF = 10MHz
Figure 4. Gain vs. LO Level, RF Frequency = 238 MHz
5.0
0
05352-039
TEMPERATURE (
C)
GAIN (
d
B)
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
20
0
20
40
60
80
40
Figure 5. Gain vs. Temperature, f
RF
= 238 MHz, f
LO
= 286 MHz
5
1
05352-005
IF FREQUENCY (MHz)
GAIN (
d
B)
6
4
3
2
50
10
100
150
200
250
300
350
RF = 238MHz
RF = 460MHz
Figure 6. Conversion Gain vs. IF Frequency
5.0
0
05352-026
VPOS (V)
GAIN (
d
B)
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
4.75
5.25
4.85
4.95
5.05
5.15
Figure 7. Gain vs. Vpos, f
RF
= 238 MHz, f
LO
= 286 MHz
50
0
3.40
3.90
05352-054
CONVERSION GAIN (238MHz)
P
E
RCE
NTAGE
45
40
35
30
25
20
15
10
5
3.45 3.50 3.55 3.60 3.65 3.70 3.75 3.80 3.85
NORMAL
MEAN = 3.7
STD. DEV. = 0.06
CONVERSION GAIN
(238MHz) PERCENTAGE
Figure 8. Conversion Gain Distribution, f
RF
= 238 MHz, f
LO
= 286 MHz
AD8342
Rev. 0 | Page 9 of 20
27
17
50
550
05352-007
RF FREQUENCY (MHz)
INPUT IP3 (
d
Bm)
100
150
200
250
300
350
400
450
500
26
25
24
23
22
21
20
19
18
IF = 10MHz
IF = 140MHz
IF = 90MHz
IF = 48MHz
Figure 9. Input IP3 vs. RF Frequency
27
17
15
5
05352-027
LO LEVEL (dBm)
INPUT IP3 (
d
Bm)
26
25
24
23
22
21
20
19
18
13
11
9
7
5
3
1
1
3
IF = 10MHz
IF = 48MHz
IF = 90MHz
140MHz
Figure 10. Input IP3 vs. LO Level, f
RF1
= 238 MHz, f
RF2
= 239 MHz
27
17
05352-032
TEMPERATURE (
C)
INPUT IP3 (
d
Bm)
20
0
20
40
60
80
40
26
25
24
23
22
21
20
19
18
Figure 11. Input IP3 vs. Temperature, f
RF1
= 238 MHz, f
RF2
= 239 MHz,
f
LO
= 286 MHz
27
17
10
05352-008
IF FREQUENCY (MHz)
INPUT IP3 (
d
Bm)
350
26
25
24
23
22
21
20
19
18
50
100
150
200
250
300
RF = 460MHz
RF = 238MHz
Figure 12. Input IP3 vs. IF Frequency
05352-028
VPOS (V)
INPUT IP3 (
d
Bm)
27
17
4.75
5.25
26
25
24
23
22
21
20
19
18
4.80 4.85 4.90 4.95 5.00 5.05 5.10 5.15 5.20
Figure 13. Input IP3 vs. Vpos, f
RF
= 238 MHz, f
RF2
= 239 MHz
LO Frequency = 286 MHz
20
0
20.6
05352-055
INPUT IP3 (238MHz)
P
E
RCE
NTAGE
18
16
14
12
10
8
6
4
2
21.0
21.4
21.8
22.2
22.6
23.0
23.4
23.8
24.2
NORMAL
MEAN = 22.7
STD. DEV. = 0.41
INPUT IP3
(238MHz) PERCENTAGE
Figure 14. Input IP3 Distribution, f
RF
= 238 MHz, f
LO
= 286 MHz
AD8342
Rev. 0 | Page 10 of 20
13
3
50
550
05352-013
RF FREQUENCY (MHz)
IN
PU
T P1dB
(
d
B
m
)
12
11
10
9
8
7
6
5
4
100
150
200
250
300
350
400
450
500
10MHz
140MHz
48MHz
90MHz
Figure 15. Input P1dB vs. RF Frequency
10.0
5.0
15
5
05352-038
LO LEVEL (dBm)
IN
PU
T P1dB
(
d
B
m
)
9.5
9.0
8.5
8.0
7.5
7.0
6.5
6.0
5.5
13
11
9
7
5
3
1
1
3
IF = 10MHz
IF = 48MHz
IF = 90MHz
IF = 140MHz
Figure 16. Input P1dB vs. LO Level, f
RF
= 238 MHz
10
0
05352-033
TEMPERATURE (
C)
IN
PU
T P1dB
(
d
B
m
)
9
8
7
6
5
4
3
2
1
20
0
20
40
60
80
40
Figure 17. Input P1dB vs. Temperature, f
RF
= 238 MHz, f
LO
= 286 MHz
10
0
10
05352-014
IF FREQUENCY (MHz)
IN
PU
T P1dB
(
d
B
m
)
9
8
7
6
5
4
3
2
1
50
100
150
200
250
300
350
RF = 460MHz
RF = 238MHz
Figure 18. Input P1dB vs. IF Frequency
05352-031
IN
PU
T P1dB
(
d
B
m
)
10
0
9
8
7
6
5
4
3
2
1
VPOS (V)
4.75
5.25
4.85
4.95
5.05
5.15
Figure 19. Input P1dB vs. Vpos, f
RF
= 238 MHz,
f
LO
= 286 MHz
28
0
8.00
05352-056
IP1dB (238MHz)
P
E
RCE
NTAGE
8.60
26
24
22
20
18
16
14
12
10
8
6
4
2
8.05 8.10 8.15 8.20 8.25 8.30 8.35 8.40 8.45 8.50 8.55
NORMAL
MEAN = 8.3
STD. DEV. = 0.07
IP1dB (238MHz)
PERCENTAGE
Figure 20. Input IP3 Distribution, f
RF
= 238 MHz, f
LO
= 286 MHz
AD8342
Rev. 0 | Page 11 of 20
60
0
100
550
05352-010
RF FREQUENCY (MHz)
INPUT IP2 (
d
Bm)
50
40
30
20
10
IF = 10MHz
IF = 140MHz
IF = 90MHz
IF = 48MHz
150
200
250
300
350
400
450
500
Figure 21. Input IP2 vs. RF Frequency (Second RF = R F - 50 MHz)
60
40
05352-029
INPUT IP2 (
d
Bm)
58
56
54
52
50
48
46
44
42
15
5
LO LEVEL (dBm)
13
11
9
7
5
3
1
1
3
IF = 10MHz
IF = 48MHz
IF = 90MHz
IF = 140MHz
Figure 22. Input IP2 vs. LO Level, f
RF
= 238 MHz, ,f
RF2
=188MHz
14.0
11.0
50
550
05352-
016
RF FREQUENCY (MHz)
NOISE F
I
GURE (d
B)
13.5
13.0
12.5
12.0
11.5
100
150
200
250
300
350
400
450
500
Figure 23. Noise Figure vs. RF Frequency, IF Frequency = 48 MHz
60
0
10
05352-011
IF FREQUENCY (MHz)
INPUT IP2 (
d
Bm)
50
40
30
20
10
50
100
150
200
250
300
350
RF = 238MHz
RF = 460MHz
Figure 24. Input IP2 vs. IF Frequency (Second RF = R F - 50 MHz)
05352-030
INPUT IP2 (
d
Bm)
60
40
58
56
54
52
50
48
46
44
42
VPOS (V)
4.75
5.25
4.85
4.95
5.05
5.15
Figure 25. Input IP2 vs. Vpos, f
RF1
= 238 MHz,
f
RF2
= 188 MHz, f
LO
= 286 MHz
16
0
10
05352-
017
IF FREQUENCY (MHz)
NOISE F
I
GURE (d
B)
14
12
10
8
6
4
2
60
110
160
210
260
310
RF = 460MHz
RF = 238MHz
Figure 26. Noise Figure vs. IF Frequency
AD8342
Rev. 0 | Page 12 of 20
16
10
15
5
05352-018
LO POWER (dBm)
NF (dB)
15
14
13
12
11
13
11
9
7
5
3
1
1
3
NF = 10MHz
NF = 48MHz
NF = 90MHz
NF = 140MHz
Figure 27. Noise Figure vs. LO Power, f
RF
= 238 MHz
5.0
0
1.8
05352-024
R
BIAS
(k
)
GAIN (
d
B)
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
2.0
2.2
2.4
2.6
2.8
3.0
3.2
3.4
Figure 28. Gain vs. R
BIAS
, RF Frequency = 238 MHz, LO Frequency = 286MHz
61
45
1.8
05352-037
R
BIAS
(k
)
INPUT IP2 (
d
Bm)
2.0
2.2
2.4
2.6
2.8
3.0
3.2
3.4
59
57
55
53
51
49
47
Figure 29. Input IP2 vs. R
BIAS
, f
RF
= 238 MHz (Second RF = RF 50MHz),
f
LO
= 286 MHz
30
0
11.8
12.8
05352-023
NOISE FIGURE (dB)
P
E
RCE
NTAGE
25
20
15
10
5
11.9 12.0 12.1 12.2 12.3 12.4 12.5 12.6 12.7
NORMAL
MEAN = 12.25
STD. DEV. = 0.14
NF PERCENTAGE
Figure 30. Noise Figure Distribution, f
RF
= 238 MHz, f
LO
= 286 MHz
30
0
1.8
3.0
05352-015
R
BIAS
(k
)
NOIS
E
FIGURE
AND INP
U
T IP
3
(dBm)
25
20
15
10
5
2.0
2.2
2.4
2.6
2.8
105
75
100
95
90
85
80
S
U
P
P
L
Y
CURRE
NT (mA)
INPUT IP3
NOISE FIGURE
CURRENT
Figure 31. Noise Figure, Input IP3 and Supply Current vs. R
BIAS
,
f
RF1
= 238 MHz, f
RF2
= 239 MHz, f
LO
= 286 MHz
10
0
1.8
05352-036
R
BIAS
(k
)
IN
PU
T P1dB
(
d
B
m
)
9
8
7
6
5
4
3
2
1
2.0
2.2
2.4
2.6
2.8
3.0
3.2
3.4
Figure 32. Input P1dB vs. R
BIAS
, f
RF
= 238 MHz, f
LO
= 286 MHz
AD8342
Rev. 0 | Page 13 of 20
0
90
50
05352-021
LO FREQUENCY (MHz)
LE
AKAGE
(dBc
)
10
20
30
40
50
60
70
80
250
450
650
850
Figure 33. LO to RF Leakage vs. LO Frequency, LO Power = 0 dBm
0
45
50
550
05352-035
RF FREQUENCY (MHz)
FE
E
D
THROUGH (dBc
)
5
10
15
20
25
30
35
40
100
150
200
250
300
350
400
450
500
IF = 10MHz
IF = 48MHz
Figure 34. RF to IF Feedthrough, RF Power =
-10 dBm
0
45
50
850
05352-020
LO FREQUENCY (MHz)
FE
E
D
THROUGH (dBc
)
5
10
15
20
25
30
35
40
150
250
350
450
550
650
750
Figure 35. LO to IF Feedthrough vs. LO Frequency, LO Power = 0 dBm
120
0
05352-034
TEMPERATURE (
C)
S
U
P
P
L
Y
CURRE
NT (mA)
20
0
20
40
60
80
40
100
80
60
40
20
Figure 36. Supply Current vs. Temperature
0
18
60
860
05352-059
LO FREQUENCY (MHz)
RE
TURN LOS
S
(dB)
2
4
6
8
10
12
14
16
160
260
360
460
560
660
760
Figure 37. LO Return Loss vs. LO Frequency
8
7
6
13
15
16
COMM
IFOP
IFOM
5
COMM
14
2
1
3
4
COMM
RFCM
RFIN
VPMX
VPDC
PWDN
EXRB
COMM
11
12
10
9
VPLO
LOCM
LOIN
COMM
AD8342
RF IN
1nF
100pF
0.1
F
100pF
0.1
F
VPOS
1nF
1nF
LO IN
TC2-1T
IF OUT
(50
)
100pF
0.1
F
VPOS
1nF
100
1.82k
100pF
VPOS
100pF
0.1
F
05352-058
Figure 38. Characterization Circuit Used to Measure TPC Data
AD8342
Rev. 0 | Page 14 of 20
CIRCUIT DESCRIPTION
The AD8342 is an active mixer optimized for operation within
the input frequency range of near dc to 500 MHz. It has a dif-
ferential, high impedance RF input that can be terminated or
matched externally. The RF input can be driven either single-
ended or differentially. The LO input is a single-ended 50
input. The IF outputs are differential open-collectors. The mixer
current can be adjusted by the value of an external resistor to
optimize performance for gain, compression, and intermodula-
tion, or for low power operation. Figure 39 shows the basic
blocks of the mixer, including the LO buffer, RF voltage-to-
current converter, bias cell, and mixing core.
The RF voltage to RF current conversion is done via a resistively
degenerated differential pair. To drive this port single-ended,
the RFCM pin should be ac-grounded while the RFIN pin is
ac-coupled to the signal source. The RF inputs can also be
driven differentially. The voltage-to-current converter then
drives the emitters of a four-transistor switching core. This
switching core is driven by an amplified version of the local
oscillator signal connected to the LO input. There are three
limiting gain stages between the external LO signal and the
switching core. The first stage converts the single-ended LO
drive to a well-balanced differential drive. The differential drive
then passes through two more gain stages, which ensures a lim-
ited signal drives the switching core. This affords the user a
lower LO drive requirement, while maintaining excellent distor-
tion and compression performance. The output signal of these
three LO gain stages drives the four transistors within the mixer
core to commutate at the rate of the local oscillator frequency.
The output of the mixer core is taken directly from its open
collectors. The open collector outputs present a high impedance
at the IF frequency. The conversion gain of the mixer depends
directly on the impedance presented to these open collectors. In
characterization, a 100 load was presented to the part via a
2:1 impedance transformer.
The device also features a power-down function. Application of
a logic low at the PWDN pin allows normal operation. A high
logic level at the PWDN pin shuts down the AD8342. Power
consumption when the part is disabled is less than 10 mW.
The bias for the mixer is set with an external resistor (R
BIAS
)
from the EXRB pin to ground. The value of this resistor directly
affects the dynamic range of the mixer. The external resistor
should not be lower than 1.82 k. Permanent damage to the
part could result if values below 1.8 k are used. This resistor
sets the dc current through the mixer core. The performance
effects of changing this resistor can be seen in the Typical Per-
formance Characteristics section.
05352-040
LO
INPUT
VPLO
IFOP
IFOM
RFIN
RFCM
BIAS
EXTERNAL
BIAS
RESISTOR
VPDC
PWDN
V
TO
I
Figure 39. Simplified Schematic Showing the Key Elements of the AD8342
As shown in Figure 40, the IF output pins, IFOP and IFOM, are
directly connected to the open collectors of the NPN transistors
in the mixer core so the differential and single-ended imped-
ances looking into this port are relatively high--on the order of
several k. A connection between the supply voltage and these
output pins is required for proper mixer core operation.
05352-041
IFOP IFOM
LOIN
RFCM
RFIN
COMM
Figure 40. AD8342 Simplified Schematic
The AD8342 has three pins for the supply voltage: VPDC,
VPMX, and VPLO. These pins are separated to minimize or
eliminate possible parasitic coupling paths within the AD8342
that could cause spurious signals or reduced interport isolation.
Consequently, each of these pins should be well bypassed and
decoupled as close to the AD8342 as possible.
AD8342
Rev. 0 | Page 15 of 20
AC INTERFACES
The AD8342 is designed to downconvert radio frequencies (RF)
to lower intermediate frequencies (IF) using a high or low-side
local oscillator (LO). The LO is injected into the mixer core at a
frequency higher or lower than the desired input RF. The
difference between the LO and the RF , f
LO
- f
RF,
(high side) or
f
RF
- f
LO
(low side) is the intermediate frequency, f
IF
. In addition
to the desired RF signal, an RF image is downconverted to the
desired IF frequency. The image frequency is at f
LO
+ f
IF
when
driven with a high side LO . When using a broadband load, the
conversion gain of the AD8342 is nearly constant over the
specified RF input band (see Figure 3).
The AD8342 is designed to operate over a broad frequency
range. It is essential to ac-couple RF and LO ports to prevent dc
offsets from skewing the mixer core in an asymmetrical man-
ner, potentially degrading noise figure and linearity.
The RF input of the AD8342 is high impedance, 1 k across the
frequency range shown in Figure 41. The input capacitance
decreases with frequency due to package parasitics.
2.00
1.00
0
0
0
1G
05352-042
FREQUENCY (Hz)
RE
S
I
S
T
ANCE
(k
)
CAP
ACITANCE
(pF)
1.75
1.50
0.75
1.25
1.00
0.50
0.75
0.50
0.25
0.25
100M 200M 300M 400M 500M 600M 700M 800M 900M
Figure 41. RF Input Impedance
The matching or termination used at the RF input of the
AD8342 has a direct effect on its dynamic range. The charac-
terization circuit, as well as the evaluation board, uses a 100
resistor to terminate the RF port. This termination resistor in
shunt with the input stage results in a return loss of better than
-10 dBm (relative to 50 ). Table 4 shows gain, IP3, P1dB, and
noise figure for four different input networks. This data was
measured at an RF frequency of 250 MHz and at an LO
frequency of 300 MHz.
Table 4. Dynamic Performance for Various Input Networks
Input
Network
50
Shunt
100
Shunt
500
Shunt
Matched
(Fig. 40)
Gain (dB)
0.66
3.5
5.3
9.3
IIP3
(dBm)
25.4 22.9 20.
6
18.5
P1dB (dBm)
10.8
8.4
6.3
2.3
NF (dB)
14
12.5
10.2
10.5
The RF port can also be matched using an LC circuit, as shown
in Figure 42.
05352-043
Z
L
1k
Z
O
= 50
f
MAIN
= 250MHz
50
3.6pF
100nH
(1000 + j0)
Figure 42. Matching Circuit
Impedance transformations of greater than 10:1 result in a
higher Q circuit and thus a narrow RF input bandwidth. A 1 k
resistor is placed across the RF input of the device in parallel
with the device internal input impedance, creating a 500 load.
This impedance is matched to as close as possible to 50 for
the source, with standard components using a shunt C, series L
matching circuit (see Figure 43).
05352-044
25.0
10.0
10.0
25.0
50.0
100.0
200.0
500.0
500.0
200.0
100.0
50.0
Q = 3.0
1
2
3
4
Point 1(1000.0 + j0.0) Q = 0.0 at 250.000 MHz
Point 2(500.0 + j0.0) Q = 0.0 at 250.000 MHz
Point 3(55.6 - j157.2) Q = 2.8 at 250.000 MHz
Point 4(55.6 - j0.1) Q = 0.0 at 250.000 MHz
Figure 43. LC Matching Example
AD8342
Rev. 0 | Page 16 of 20
IF PORT
The IF port comprises open-collector differential outputs. The
NPN open collectors can be modeled as current sources that are
shunted with resistances of ~10 k in parallel with capacitances
of ~1 pF.
The specified performance numbers for the AD8342 were
measured with 100 differential terminations. However, dif-
ferent load impedances may be used where circumstances dic-
tate. In general, lower load impedances result in lower conver-
sion gain and lower output P1dB. Higher load impedances
result in higher conversion gain for small signals, but lower IP3
values for both input and output.
If the IF signal is to be delivered to a remote load, more than a
few millimeters away at high output frequencies, avoid unin-
tended parasitic effects due to the intervening PCB traces. One
approach is to use an impedance transforming network or
transformer located close to the AD8342. If very wideband out-
put is desired, a nearby buffer amplifier may be a better choice,
especially if IF response to dc is required. An example of such a
circuit is presented in Figure 45, in which the AD8351 differen-
tial amplifier is used to drive a pair of 75 transmission lines.
The gain of the buffer can be independently set by appropriate
choice of the value for the gain resistor, R
G
.
50
0.5
0
0
1G
05352-045
FREQUENCY (Hz)
RE
S
I
S
T
ANCE
(k
)
CAP
ACITANCE
(pF)
45
0.4
40
0.3
35
0.2
30
0.1
25
0
20
0.1
15
0.2
10
5
100M 200M 300M 400M 500M 600M 700M 800M 900M
Figure 44. IF Port Impedance
05352-046
COMM
8
IFOP
7
IFOM
6
COMM
5
AD8342
AD8351
+
RFC
+V
S
RFC
Z
L
= 100
+V
S
+V
S
100
R
G
Z
L
Tx LINE Z
O
= 75
Tx LINE Z
O
= 75
Figure 45. AD8351 Used as Transmission Line Driver and Impedance Buffer
The high input impedance of the AD8351 allows for a shunt
differential termination to provide the desired 100 load to the
AD8342 IF output port.
It is necessary to bias the open-collector outputs using one of
the schemes presented in Figure 47 and Figure 48. Figure 47
illustrates the application of a center tapped impedance trans-
former. The turns ratio of the transformer should be selected to
provide the desired impedance transformation. In the case of a
50 load impedance, a 2-to-1 impedance ratio transformer
should be used to transform the 50 load into a 100 differ-
ential load at the IF output pins. Figure 48 illustrates a differen-
tial IF interface where pull-up choke inductors are used to bias
the open-collector outputs. The shunting impedance of the
choke inductors used to couple dc current into the mixer core
should be large enough at the IF operating frequency so it does
not load down the output current before reaching the intended
load. Additionally, the dc current handling capability of the
selected choke inductors needs to be at least 45 mA. The self-
resonant frequency of the selected choke should be higher than
the intended IF frequency. A variety of suitable choke inductors
are commercially available from manufacturers such as Murata
and Coilcraft. Figure 46 shows the loading effects when using
nonideal inductors. An impedance transforming network may
be required to transform the final load impedance to 100 at
the IF outputs. There are several good reference books that
explain general impedance matching procedures, including:
Chris Bowick, RF Circuit Design, Newnes, Reprint Edition,
1997.
David M. Pozar, Microwave Engineering, Wiley Text Books,
Second Edition, 1997.
Guillermo Gonzalez, Microwave Transistor Amplifiers:
Analysis and Design, Prentice Hall, Second Edition, 1996.
05352-049
0
180
30
330
50MHz
50MHz
500MHz
500MHz
60
90
270
300
120
240
150
210
REAL
CHOKES
IDEAL
CHOKES
Figure 46. IF Port Loading Effects Due to Finite Q Pull-Up Inductors
(Murata BLM18HD601SN1D Chokes)
AD8342
Rev. 0 | Page 17 of 20
05352-047
COMM
8
IFOP
7
IFOM
6
COMM
5
AD8342
Z
L
= 100
IF OUT
Z
O
= 50
+V
S
2:1
Figure 47. Biasing the IF Port Open-Collector Outputs
Using a Center-Tapped Impedance Transformer
05352-048
COMM
8
IFOP
7
IFOM
6
COMM
5
AD8342
RFC
+V
S
RFC
Z
L
= 100
IF OUT+
IF OUT
+V
S
Z
L
IMPEDANCE
TRANSFORMING
NETWORK
Figure 48. Biasing the IF Port Open-Collector Outputs
Using Pull-Up Choke Inductors
The AD8342 is optimized for driving a 100 load. Although
the device is capable of driving a wide variety of loads, to main-
tain optimum distortion and noise performance, it is advised
that the presented load at the IF outputs is close to 100 . The
linear differential voltage conversion gain of the mixer can be
modeled as
LOAD
m
R
G
Av
=
where:
e
m
m
m
R
g
g
G
+
=
1
1
R
LOAD
is the single-ended load impedance.
g
m
is the transistor transconductance and is equal to
1810/R
BIAS
.
R
e
is 15 .
The external R
BIAS
resistor is used to control the power dissipa-
tion and dynamic range of the AD8342. Because the AD8342
has internal resistive degeneration, the conversion gain is pri-
marily determined by the load impedance and the on-chip
degeneration resistors. Figure 49 shows how gain varies with IF
load. The external R
BIAS
resistor has only a small effect. The
most direct way to affect conversion gain is by varying the load
impedance. Small loads result in lower gains while larger loads
increase the conversion gain. If the IF load impedance is too
large it causes a decrease in linearity (P1dB, IP3). In order to
maintain positive conversion gain and preserve SFDR perform-
ance, the differential load presented at the IF port should
remain in the range of ~ 100 to 250 .
30
0
10
1000
05352-057
IF LOAD (
)
VOLTAGE GAIN (
d
B)
100
25
20
15
10
5
MEASURED
MODELED
Figure 49. Voltage Conversion Gain vs. IF Loading
LO CONSIDERATIONS
The LOIN port provides a 50 load impedance with common-
mode decoupling on LOCM. Again, common-grade ceramic
capacitors provide sufficient signal coupling and bypassing of
the LO interface.
The LO signal needs to have adequate phase noise characteris-
tics and low second-harmonic content to prevent degradation
of the noise figure performance of the AD8342. An LO plagued
with poor phase noise can result in reciprocal mixing, a mecha-
nism that causes spectral spreading of the downconverted sig-
nal, limiting the sensitivity of the mixer at frequencies close-in
to any large input signals. The internal LO buffer provides
enough gain to hard-limit the input LO and provide fast switch-
ing of the mixer core. Odd harmonic content present on the LO
drive signal should not impact mixer performance; however,
even-order harmonics cause the mixer core to commutate in an
unbalanced manner, potentially degrading noise performance.
Simple lumped element low-pass filtering can be applied to help
reject the harmonic content of a given local oscillator, as shown
in Figure 50. The filter depicted is a common 3-pole Chebyshev,
designed to maintain a 1-to-1 source-to-load impedance ratio
with no more than 0.5 dB of ripple in the pass band. Other filter
structures can be effective as long as the second harmonic of the
LO is filtered to negligible levels, for example, ~30 dB below the
fundamental.
05352-050
AD8342
LOIN
3
COMM
4
LOCM
2
R
L
FOR R
S
= R
L
f
C
- FILTER CUTOFF FREQUENCY
R
S
C1
C3
LO
SOURCE
L2
C1 =
1.864
2
f
cR
L
C3 =
1.834
2
f
cR
L
L2 =
1.28R
L
2
f
c
Figure 50. Using a Low-Pass Filter to Reduce LO Second Harmonic
AD8342
Rev. 0 | Page 18 of 20
HIGH IF APPLICATIONS
In some applications it may be desirable to use the AD8342 as
an up-converting mixer. The AD8342 is a broadband mixer
capable of both up and down conversion. Unlike other mixers
that rely on on-chip reactive circuitry to optimize performance
over a specific band, the AD8342 is a versatile general-purpose
device that can be used from arbitrarily low frequencies to sev-
eral GHz. In general, the following considerations help to en-
sure optimum performance:
Minimize ac loading impedance of IF port bias network.
Maximize power transfer to the desired ac load.
For maximum conversion gain and the lowest noise per-
formance reactively match the input as described in the
IF Port section.
For maximum input compression point and input intercept
points resistively terminate the input as described in the
IF Port section.
As an example, Figure 51 shows the AD8342 as an up-
converting mixer for a WCDMA single-carrier transmitter de-
sign. For this application, it was desirable to achieve -65 dBc
adjacent channel power ratio (ACPR) at a -13 dBm output
power level. The ACPR is a measure of both distortion and
noise carried into an adjacent frequency channel due to the
finite intercept points and noise figure of an active device.
8
7
6
13
15
16
COMM
IFOP
IFOM
5
COMM
14
2
1
3
4
COMM
RFCM
RFIN
VPMX
VPDC
PWDN
EXRB
COMM
11
12
10
9
VPLO
LOCM
LOIN
COMM
AD8342
05352-
052
VPOS
VPOS
34nH
34nH
100pF
100pF
1nF
1nF
ETC1-1-13
100pF
100pF
0.1
F
VPOS
1nF
1nF
1970MHz
OSC
1.82k
100pF
4.7pF
170MHz
INPUT
100nH
1nF
499
VPOS
100pF
0.1pF
2140MHz OUT
1nF
Figure 51. WCDMA Tx Up-Conversion Application Circuit
Because a WCDMA channel encompasses a bandwidth of
almost 5 MHz, it is necessary to keep the Q of the matching
circuit low enough so that phase and magnitude variations are
below an acceptable level over the 5 MHz band. It is possible
to use purely reactive matching to transform a 50 source
to match the raw ~1 k input impedance of the AD8342.
However, the L and C component variations could present
production concerns due to the sensitivity of the match. For
this application, it is advantageous to shunt down the ~1 k
input impedance using an external shunt termination resistor
to allow for a lower Q reactive matching network. The input is
terminated across the RFIN and RFCM pins using a 499
termination. The termination should be as close to the device as
possible to minimize standing wave concerns. The RFCM is
bypassed to ground using a 1 nF capacitor. A dc blocking ca-
pacitor of 1 nF is used to isolate the dc input voltage present on
the RFIN pin from the source. A step-up impedance transfor-
mation is realized using a series L shunt C reactive network.
The actual values used need to accommodate for the series L
and stray C parasitics of the connecting transmission line seg-
ments. When using the customer evaluation board with the
components specified in Figure 51, the return loss over a 5 MHz
band centered at 170 MHz was better than 10 dB.
External pull-up choke inductors are used to feed dc bias into
the open-collector outputs. It is desirable to select pull-up choke
inductors that present high loading reactance at the output
frequency. Coilcraft 0302CS series inductors were selected due
to their very high self-resonant frequency and Q. A 1:1 balun
was ac-coupled to the output to convert the differential output
to a single-ended signal and present the output with a 50
ac loading impedance.
The performance of the circuit is shown in Figure 52. The aver-
age ACPR of the adjacent and alternate channels is presented
vs. output power. The circuit provides a 65 dBc ACPR at
-13 dBm output power. The optimum ACPR power level can be
shifted to the right or left by adjusting the output loading and
the loss of the input match.
60
70
25
0
05352-
053
OUTPUT POWER (dBm)
ACPR (dBc)
62
64
66
68
20
15
10
5
ADJACENT
CHANNELS
ALTERNATE
CHANNELS
Figure 52. Single Carrier WCDMA ACPR Performance of Tx Up-Conversion
Circuit (Test Model 1_64)
AD8342
Rev. 0 | Page 19 of 20
EVALUATION BOARD
An evaluation board is available for the AD8342. The evaluation board is configured for single-ended signaling at the IF output port via a
balun transformer. The schematic for the evaluation board is presented in Figure 53.
R2
0
R1
0
C6
1000pF
C4
1000pF
C1
1000pF
C3
1000pF
C5
0.1
F
C2
0.1
F
VPOS
RF_IN
C7
1000pF
INLO
C8
1000pF
C9
0.1
F
C10
100pF
VPOS
R11
0
R16
0
R10
0
R12
OPEN
Z4
OPEN
R4
OPEN
3
4
1
6
2
TC2-1T
Z2
OPEN
R3
OPEN
100
TRACES,
NO GROUND PLANE
IF_OUT+
IF_OUT
R15
0
T1
Z1
OPEN
Z3
OPEN
R5
100
C14
OPEN
L1
0
COMM
IFOP
IFOM
COMM
COMM
RFCM
RFIN
VPMX
VPDC PWDN EXRB COMM
VPLO LOCM LOIN COMM
DUT
12
11
10
9
13
14
15
16
1
2
3
4
8
7
6
5
R6
1.82k
C11
100pF
R7
0
C13
100pF
C12
0.1
F
VPOS
GND
PWDN
VPOS
W1
R8
10k
R9
0
PWDN
05352-003
50
TRACE
Figure 53. Evaluation Board
Table 6. Evaluation Board Configuration Options
Component
Function
Default Conditions
R1, R2, R7,
C2, C4, C5, C6, C10
C12, C13, C14, C9
Supply decoupling. Shorts or power supply decoupling resistors and filter
capacitors.
R1, R2, R7 = 0
C4, C6 = 1000 pF
C10, C13 = 100 pF
C2, C5, C12, C9 = 0.1 F
R3, R4
Options for single-ended IF output circuit.
R3, R4 = Open
R15, 16
R15, R16 = 0
R6, C11
R
BIAS
resistor that sets the bias current for the mixer core. The capacitor
provides ac bypass for R6.
R6 = 1.82 k
C11 = 100 pF
R8
Pull down for the PWDN pin.
R8 = 10 k
R9
Link to PWDN pin.
R9 = 0
C3, R5, C16, L1
RF input. C3 provides dc block for RF input. R5 provides a resistive input
termination. C16 and L1 are provided for reactive matching the input.
C3 = 1000 pF
R5 = 100
C14 = Open
L1 = 0
C1
RF common ac coupling. Provides dc block for RF input common
connection.
C1 = 1000 pF
C8
C7
LO input ac coupling. Provides dc block for the LO input.
LO common ac coupling. Provides dc block for LO input common
connection.
C7, C8 = 1000 pF
W1
Power down. The part is on when the PWDN is connected to ground via a
10 k resistor. The part is disabled when PWDN is connected to the positive
supply (V
S
) via W1.
T1, R12, R11, Z3,
Z4, Z1, Z2, R10
IF output interface. T1 converts a differential high impedance IF output to
single-ended. When loaded with 50 , this balun presents a 100 load to
the mixers collectors. The center tap of the primary is used to supply the
bias voltage (V
S
) to the IF output pins.
T1 = TC2-1T, 2:1 (Mini-Circuits)
R12 = Open
R10, R11 = 0
Z3, Z4 = Open
Z1, Z2 = Open
AD8342
Preliminary Technical Data
Rev. 0 | Page 20 of 20
OUTLINE DIMENSIONS
1
0.50
BSC
0.60 MAX
PIN 1
INDICATOR
1.50 REF
0.50
0.40
0.30
0.25 MIN
0.45
2.75
BSC SQ
TOP
VIEW
12 MAX
0.80 MAX
0.65 TYP
SEATING
PLANE
PIN 1
INDICATOR
0.90
0.85
0.80
0.30
0.23
0.18
0.05 MAX
0.02 NOM
0.20 REF
3.00
BSC SQ
*1.65
1.50 SQ
1.35
16
5
13
8
9
12
4
EXPOSED
PAD
(BOTTOM VIEW)
*COMPLIANT TO JEDEC STANDARDS MO-220-VEED-2
EXCEPT FOR EXPOSED PAD DIMENSION.
Figure 54. 16-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
3 mm x 3 mm Body, Very Thin Quad
(CP-16-3)
Dimensions in millimeters
ORDERING GUIDE
Models
Temperature
Package
Package Description
Package
Outline
Branding
Transport Media,
Quanity
AD8342ACPZ-REEL7
1
-40C to +85C
16-Lead Lead Frame Chip Scale Package
[LFCSP_VQ]
CP-16-3
Q01
1,500, Reel
AD8342ACPZ-R2
1
-40C to +85C
16-Lead Lead Frame Chip Scale Package
[LFCSP_VQ]
CP-16-3
Q01
250, Reel
AD8342ACPZ-WP
1
-40C to +85C
16-Lead Lead Frame Chip Scale Package
[LFCSP_VQ]
CP-16-3
Q01
50, Waffle Pack
AD8342-EVAL
Evaluation Board
1
1
Z = Pb-free part.
2005 Analog Devices, Inc. All rights reserved. Trademarks and
regis-
tered trademarks are the property of their respective owners.
D0535204/05(0)
PDF 
ZIP