FUNCTIONAL BLOCK DIAGRAM

(DIP Package)

AD1865

TRIM

MSB

DGND

AGND

OUT

TRIM

MSB

CLK

AGND

18-BIT

LATCH

18-BIT

D/A

REFERENCE

18-BIT

LATCH

18-BIT

D/A

REFERENCE

NC = NO CONNECT

REV. 0

Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.

Complete Dual 18-Bit

16 F

Audio DAC

AD1865*

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 617/329-4700

Fax: 617/326-8703

FEATURES
Dual Serial Input, Voltage Output DACs
No External Components Required
110 dB SNR
0.003% THD+N
Operates at 16 Oversampling per Channel

5 Volt Operation

Cophased Outputs
116 dB Channel Separation
Pin Compatible with AD1864
DIP or SOIC Packaging

APPLICATIONS
Multichannel Audio Applications
Compact Disc Players
Multivoice Keyboard Instruments
DAT Players and Recorders
Digital Mixing Consoles
Multimedia Workstations

PRODUCT DESCRIPTION

The AD1865 is a complete, dual 18-bit DAC offering excellent
THD+N and SNR while requiring no external components. Two
complete signal channels are included. This results in cophased
voltage or current output signals and eliminates the need for
output demultiplexing circuitry. The monolithic AD1865 chip
includes CMOS logic elements, bipolar and MOS linear ele-
ments and laser-trimmed thin-film resistor elements, all fabri-
cated on Analog Devices' ABCMOS process.

The DACs on the AD1865 chip employ a partially segmented
architecture. The first four MSBs of each DAC are segmented
into 15 elements. The 14 LSBs are produced using standard R-2R
techniques. Segment and R-2R resistors are laser trimmed to pro-
vide extremely low total harmonic distortion. This architecture
minimizes errors at major code transitions resulting in low out-
put glitch and eliminating the need for an external deglitcher.
When used in the current output mode, the AD1865 provides
two

1 mA output signals.

Each channel is equipped with a high performance output am-
plifier. These amplifiers achieve fast settling and high slew rate,
producing

3 V signals at load currents up to 8 mA. Each out-

put amplifier is short-circuit protected and can withstand indefi-
nite short circuits to ground.

The AD1865 was designed to balance two sets of opposing re-
quirements, channel separation and DAC matching. High chan-
nel separation is the result of careful layout. At the same time,
both channels of the AD1865 have been designed to ensure
matched gain and linearity as well as tracking over time and
temperature. This assures optimum performance when used in
stereo and multi-DAC per channel applications.

*Protected by U.S. Patents Nos.: RE 30,586; 3,961,326; 4,141,004;

4,349,811; 4,855,618; 4,857,862.

A versatile digital interface allows the AD1865 to be directly
connected to standard digital filter chips. This interface employs
five signals: Data Left (DL), Data Right (DR), Latch Left (LL),
Latch Right (LR) and Clock (CLK). DL and DR are the serial
input pins for the left and right DAC input registers. Input data
bits are clocked into the input register on the rising edge of
CLK. A low-going latch edge updates the respective DAC out-
put. For systems using only a single latch signal, LL and LR
may be connected together. For systems using only one DATA
signal, DR and DL may be connected together.

The AD1865 operates with

5 V power supplies. The digital

supply, V

, can be separated from the analog supplies, V

and

, for reduced digital feedthrough. Separate analog and digital

ground pins are also provided. The AD1865 typically dissipates
only 225 mW, with a maximum power dissipation of 260 mW.

The AD1865 is packaged in both a 24-pin plastic DIP and a
28-pin SOIC package. Operation is guaranteed over the temper-
ature range of 25

C to +70

C and over the voltage supply

range of

4.75 V to

5.25 V.

PRODUCT HIGHLIGHTS

1. The AD1865 is a complete dual 18-bit audio DAC.

2. 110 dB signal-to-noise ratio for low noise operation.

3. THD+N is typically 0.003%.

4. Interchannel gain and midscale matching.

5. Output voltages and currents are cophased.

6. Low glitch for improved sound quality.

7. Both channels are 100% tested at 16

8. Low Power--only 225 mW typ, 260 mW max.

9. Five-wire interface for individual DAC control.

10. 24-pin DIP or 28-pin SOIC packages available.

REV. 0

AD1865SPECIFICATIONS

= +25 C, +V

= +V

= +5 V and V

= 5 V, F

= 705.6 kHz, no MSB adjustment

or deglitcher)

Parameter

Min

Typ

Max

Unit

RESOLUTION

Bits

DIGITAL INPUTS V

2.0

0.8

, V

= +V

1.0

, V

= 0.4 V

10

Clock Input Frequency

13.5

MHz

ACCURACY

Gain Error

0.2

1.0

% of FSR

Interchannel Gain Matching

0.3

0.8

% of FSR

Midscale Error

Interchannel Midscale Matching

Gain Linearity (0 dB to 90 dB)

DRIFT (0

C to +70

Gain Drift

ppm of FSR/

Midscale Drift

ppm of FSR/

TOTAL HARMONIC DISTORTION + NOISE*

0 dB, 990.5 Hz

AD1865N, R

0.004

0.006

AD1865N-J, R-J

0.003

0.004

20 dB, 990.5 Hz

AD1865N, R

0.010

0.040

AD1865N-J, R-J

0.010

0.020

60 dB, 990.5 Hz AD1865N, R

1.0

4.0

AD1865N-J, R-J

1.0

2.0

CHANNEL SEPARATION*

0 dB, 990.5 Hz

110

116

SIGNAL-TO-NOISE RATIO* (20 Hz to 30 kHz)

107

110

D-RANGE* (With A-Weight Filter)

60 dB, 990.5 Hz AD1865N, R

100

AD1865N-J, R-J

100

OUTPUT

Voltage Output Configuration

Output Range (

1%)

2.94

3.0

3.06

Output Impedance

0.1

Load Current

Short Circuit Duration

Indefinite to Common

Current Output Configuration

Bipolar Output Range (

30%)

Output Impedance (

30%)

1.7

POWER SUPPLY

and +V

4.75

5.0

5.25

5.0

4.75

+I, +V

and +V

= +5 V

I, V

= 5 V

26

POWER DISSIPATION, +V

= +V

= +5 V, V

= 5 V

225

260

TEMPERATURE RANGE

Specification

+25

+70

Operation

+70

Storage

+100

WARMUP TIME

min

Specifications shown in boldface are tested on production units at final test without optional MSB adjustment.
*Tested in accordance with EIAJ Test Standard CP-307 with 18-bit data.
Specifications subject to change without notice.

AD1865

REV. 0

ABSOLUTE MAXIMUM RATINGS*

to DGND . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 V to 6.0 V

to AGND . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 V to 6.0 V

to AGND . . . . . . . . . . . . . . . . . . . . . . . . . . 6.0 V to 0 V

AGND to DGND . . . . . . . . . . . . . . . . . . . . . . . . . . . .

0.3 V

Digital Inputs to DGND . . . . . . . . . . . . . . . . . . . . . 0.3 to V

Short Circuit Protection . . . . . . . . Indefinite Short to Ground
Soldering (10 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . . +300

*Stresses greater than those listed under "Absolute Maximum Ratings" may cause

permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other conditions above those indicated in the
operational section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.

WARNING!

ESD SENSITIVE DEVICE

CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the AD1865 features proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.

ORDERING GUIDE

Temperature

Package

Model

Range

THD+N @ FS

Option*

AD1865N

C to +70

0.006%

N-24A

AD1865N-J

C to +70

0.004%

N-24A

AD1865R

C to +70

0.006%

R-28

AD1865R-J

C to +70

0.004%

R-28

*N = Plastic DIP, R = Small Outline IC Package.

PIN DESIGNATIONS

DIP SOIC

Negative Analog Supply

TRIM

Right Channel Trim Network Connection

MSB

Right Channel Trim Potentiometer
Wiper Connection

OUT

Right Channel Output Current

AGND Analog Common Pin

Right Channel Amplifier Summing Junction

Right Channel Feedback Resistor

OUT

Right Channel Output Voltage

Positive Digital Supply

Right Channel Data Input Pin

Right Channel Latch Pin

CLK

Clock Input Pin

DGND Digital Common Pin

Left Channel Latch Pin

Left Channel Data Input Pin

11, 16, 18 NC

No Internal Connection*

25, 27

OUT

Left Channel Output Voltage

Left Channel Feedback Resistor

Left Channel Amplifier Summing Junction

AGND Analog Common Pin

OUT

Left Channel Output Current

MSB

Left Channel Trim Potentiometer
Wiper Connection

TRIM

Left Channel Trim Network Connection

Positive Analog Supply

*Pin 16 has no internal connection; V

from AD1864 DIP socket can be safely

applied.

PINOUT

(24-Pin DIP Package)

TOP VIEW

(Not to Scale)

AD1865

TRIM

MSB

DGND

AGND

OUT

TRIM

MSB

CLK

AGND

LEFT
CHANNEL

RIGHT

CHANNEL

NC = NO CONNECT

(28-Pin SOIC Package)

TOP VIEW

(Not to Scale)

AD1865

OUT

CLK

DGND

OUT

AGND

OUT

MSB

TRIM

MSB

OUT

AGND

NC = NO CONNECT

AD1865

REV. 0

TOTAL HARMONIC DISTORTION + NOISE

Total harmonic distortion plus noise (THD+N) is defined as
the ratio of the square root of the sum of the squares of the am-
plitudes of the harmonics and noise to the value of the funda-
mental input frequency. It is usually expressed in percent.

THD+N is a measure of the magnitude and distribution of lin-
earity error, differential linearity error, quantization error and
noise. The distribution of these errors may be different, depend-
ing on the amplitude of the output signal. Therefore, to be most
useful, THD+N should be specified for both large (0 dB) and
small (20 dB, 60 dB) signal amplitudes. THD+N measure-
ments for the AD1865 are made using the first 19 harmonics
and noise out to 30 kHz.

SIGNAL-TO-NOISE RATIO

The signal-to-noise ratio is defined as the ratio of the amplitude
of the output when a full-scale code is entered to the amplitude
of the output when a midscale code is entered. It is measured
using a standard A-Weight filter. SNR for the AD1865 is mea-
sured for noise components out to 30 kHz.

CHANNEL SEPARATION

Channel separation is defined as the ratio of the amplitude of a
full-scale signal appearing on one channel to the amplitude of
that same signal which couples onto the adjacent channel. It is
usually expressed in dB. For the AD1865 channel separation is
measured in accordance with EIAJ Standard CP-307, Section
5.5.

D-RANGE DISTORTION

D-Range distortion is equal to the value of the total harmonic
distortion + noise (THD+N) plus 60 dB when a signal level of
60 dB below full scale is reproduced. D-Range is tested with a
1 kHz input sine wave. This is measured with a standard A-Weight
filter as specified by EIAJ Standard CP-307.

GAIN ERROR

The gain error specification indicates how closely the output of
a given channel matches the ideal output for given input data. It
is expressed in % of FSR and is measured with a full-scale out-
put signal.

INTERCHANNEL GAIN MATCHING

The gain matching specification indicates how closely the ampli-
tudes of the output signals match when producing identical in-
put data. It is expressed in % of FSR (Full-Scale Range = 6 V
for the AD1865) and is measured with full-scale output signals.

MIDSCALE ERROR

Midscale error is the deviation of the actual analog output of a
given channel from the ideal output (0 V) when the twos
complement input code representing half scale is loaded into the
input register of the DAC. It is expressed in mV and is mea-
sured with half-scale output signals.

INTERCHANNEL MIDSCALE MATCHING

The midscale matching specification indicates how closely the
amplitudes of the output signals of the two channels match
when the twos complement input code representing half scale is
loaded into the input register of both channels. It is expressed in
mV and is measured with half-scale output signals.

FUNCTIONAL DESCRIPTION

The AD1865 is a complete, monolithic, dual 18-bit audio DAC.
No external components are required for operation. As shown in
the block diagram, each chip contains two voltage references,
two output amplifiers, two 18-bit serial input registers and two
18-bit DACs.

The voltage reference section provides a reference voltage for
each DAC circuit. These voltages are produced by low-noise
bandgap circuits. Buffer amplifiers are also included. This com-
bination of elements produces reference voltages that are unaf-
fected by changes in temperature and age.

The output amplifiers use both MOS and bipolar devices and
incorporate an all NPN output stage. This design technique
produces higher slew rate and lower distortion than previous
techniques. Frequency response is also improved. When com-
bined with the appropriate on-chip feedback resistor, the output
op amps convert the output current to output voltages.

The 18-bit D/A converters use a combination of segmented de-
coder and R-2R architecture to achieve consistent linearity and
differential linearity. The resistors which form the ladder struc-
ture are fabricated with silicon chromium thin film. Laser trim-
ming of these resistors further reduces linearity errors resulting
in low output distortion.

The input registers are fabricated with CMOS logic gates.
These gates allow the achievement of fast switching speeds and
low power consumption, contributing to the low glitch and low
power dissipation of the AD1865.

AD1865

TRIM

MSB

DGND

AGND

OUT

TRIM

MSB

CLK

AGND

18-BIT

LATCH

18-BIT

D/A

REFERENCE

18-BIT

LATCH

18-BIT

D/A

REFERENCE

NC = NO CONNECT

AD1865 Block Diagram (DIP Package)

GROUNDING RECOMMENDATIONS

The AD1865 has three ground pins, two labeled AGND and
one labeled DGND. AGND, the analog ground pins, are the
"high quality" ground references for the device. To minimize
distortion and reduce crosstalk between channels, the analog
ground pins should be connected together only at the analog
common point in the system. As shown in Figure 6, the AGND
pins should not be connected at the chip.

AD1865

NC = NO CONNECT

TRIM

MSB

OUT

AGND

OUT

CLK

TRIM

MSB

OUT

AGND

OUT

DGND

ANALOG

SUPPLY

DIGITAL
SUPPLY

OUT

ANALOG
SUPPLY

OUT

DIGITAL
COMMON

Figure 6. Recommended Circuit Schematic

The digital ground pin returns ground current from the digital
logic portions of the AD1865 circuitry. This pin should be con-
nected to the digital common pin in the system. Other digital
logic chips should also be referred to that point. The analog and
digital grounds should be connected together at one point in the
system, preferably at the power supply.

POWER SUPPLIES AND DECOUPLING

The AD1865 has three power supply input pins.

provides

the supply voltages which operate the analog portions of the
DAC including the voltage references, output amplifiers and
control amplifiers. The

supplies are designed to operate

from

5 V supplies. Each supply should be decoupled to analog

common using a 0.1

F capacitor in parallel with a 10

capacitor. Good engineering practice suggests that the bypass
capacitors be placed as close as possible to the package pins.
This minimizes the parasitic inductive effects of printed circuit
board traces.

The +V

supply operates the digital portions of the chip includ-

ing the input shift registers and the input latching circuitry.
This supply should be bypassed to digital common using a
0.1

F capacitor in parallel with a 10

F capacitor. +V

oper-

ates with a +5 V supply. In order to assure proper operation of
the AD1865, V

must be the most negative power supply volt-

age at all times.

Though separate positive power supply pins are provided for
the analog and digital portions of the AD1865, it is also possible
to use the AD1865 in systems featuring a single +5 V power
supply. In this case, both the +V

and +V

input pins should be

connected to the single +5 V power supply. This feature allows
reduction of the cost and complexity of the system power
supply.

AD1865Analog Circuit Consideration

REV. 0

As with most linear circuits, changes in the power supplies will
affect the output of the DAC. Analog Devices recommends that
well regulated power supplies with less than 1% ripple be incor-
porated into the design of an audio system.

DISTORTION PERFORMANCE AND TESTING

The THD+N figure of an audio DAC represents the amount of
undesirable signal produced during reconstruction and playback
of an audio waveform. The THD+N specification, therefore,
provides a direct method to classify and choose an audio DAC
for a desired level of performance. Figure 1 illustrates the typ-
ical THD+N performance of the AD1865 versus frequency. A
load impedance of at least 1.5 k

is recommended for best

THD+N performance.

Analog Devices tests and grades all AD1865s on the basis of
THD+N performance. During the distortion test, a high-speed
digital pattern generator transmits digital data to each channel
of the device under test. Eighteen-bit data is transmitted at
705.6 kHz (16

). The test waveform is a 990.5 Hz sine wave

with 0 dB, 20 dB and 60 dB amplitudes. A 4096 point FFT
calculates total harmonic distortion + noise, signal-to-noise ratio,
D-Range and channel separation. No deglitchers or MSB trims
are used in the testing of the AD1865.

OPTIONAL MSB ADJUSTMENT

Use of optional adjust circuitry allows residual distortion error
to be eliminated. This distortion is especially important when
low amplitude signals are being reproduced. The MSB adjust
circuitry is shown in Figure 7. The trim potentiometer should
be adjusted to produce the lowest distortion using an input sig-
nal with a 60 dB amplitude.

AD1865

NC = NO CONNECT

TRIM

MSB

OUT

AGND

OUT

CLK

TRIM

MSB

OUT

AGND

OUT

DGND

200k

100k

470k

100k

200k

Figure 7. Optional THD+N Adjust Circuitry

REV. 0

CURRENT OUTPUT MODE

One or both channels of the AD1865 can be operated in current
output mode. I

OUT

can be used to directly drive an external

current-to-voltage (I-V) converter. The internal feedback resis-
tor, R

, can still be used in the feedback path of the external I-V

converter, thus assuring that R

tracks the DAC over time and

temperature.

Of course, the AD1865 can also be used in voltage output mode
in order to utilize the onboard I-V converter.

VOLTAGE OUTPUT MODES

As shown on the block diagram, each channel of the AD1865 is
complete with an I-V converter and a feedback resistor. These
can be connected externally to provide direct voltage output
from one or both AD1865 channels. Figure 6 shows these con-
nections. I

OUT

is connected to the Summing Junction, SJ. V

OUT

is connected to the feedback resistor, R

This implementation

results in the lowest possible component count and achieves the
specifications shown on the Specifications page while operating
at 16

S
B

CLK

Figure 8. AD1865 Control Signals

INPUT DATA

Data is transmitted to the AD1865 in a bit stream composed of
18-bit words with a serial, twos complement, MSB first format.
Data Left (DL) and Data Right (DR) are the serial inputs for
the left and right DACs, respectively. Similarly, Latch Left (LL)
and Latch Right (LR) update the left and right DACs. The fall-
ing edge of LL and LR cause the last 18 bits which were clocked
into the Serial Registers to be shifted into the DACs, thereby
updating the DAC outputs. Left and Right channels share the
Clock (CLK) signal. Data is clocked into the input registers on
the rising edge of CLK.

Figure 8 illustrates the general signal requirements for data
transfer for the AD1865.

TIMING

Figure 9 illustrates the specific timing requirements that must
be met in order for the data transfer to be accomplished prop-
erly. The input pins of the AD1865 are both TTL and 5 V
CMOS compatible.

The minimum clock rate of the AD1865 is at least 13.5 MHz.
This clock rate allows data transfer rates of 2

, 4

, 8

and

(where F

equals 44.1 kHz).

CLK

DL/DR

LL/LR

>74.1ns

>30ns

>40ns

>15ns

>40ns

>30ns

>15ns

MSB

1st BIT

2nd BIT

LSB

18th BIT

NEXT

WORD

BITS CLOCKED
TO SHIFT REGISTER

INTERNAL DAC INPUT REGISTER

UPDATED WITH 18 MOST RECENT BITS

Figure 9. AD1865 Timing Diagram

Digital Circuit ConsiderationsAD1865

AD1865

REV. 0

18-BIT CD PLAYER DESIGN

Figure 10 illustrates an 18-bit CD player design incorporating
an AD1865 D/A converter, an NE5532 dual op amp and the
SM5813 digital filter chip manufactured by NPC. In this de-
sign, the SM5813 filter transmits left and right digital data to
both channels of the AD1865. The left and right latch signals,
LL and LR, are both provided by the word clock signal
(WCKO) of the digital filter. The digital filter supplies data at
an 8

oversample rate to each channel.

The digital data is converted to analog output voltages by the
output amplifiers on the AD1865. Note that no external compo-
nents are required by the AD1865. Also, no deglitching cir-
cuitry is required.

An NE5532 dual op amp is used to provide the output antialias
filters required for adequate image rejection. One 2-pole filter
section is provided for each channel. An additional pole is cre-
ated from the combination of the internal feedback resistors
(R

) and the external capacitors C1 and C2. For example, the

nominal 3 k

with a 360 pF capacitor for C1 and C2 will

place a pole at approximately 147 kHz, effectively eliminating
all high frequency noise components.

Low distortion, superior channel separation, low power con-
sumption and a low parts count are all realized by this simple
design.

AD1865

TRIM

MSB

DGND

AGND

OUT

TRIM

MSB

CLK

AGND

LEFT
CHANNEL
OUTPUT

RIGHT
CHANNEL
OUTPUT

5V ANALOG SUPPLY

+5V ANALOG SUPPLY

+5V DIGITAL

SUPPLY

BCKO

WCKO

DOL

DOR

OW20

SM5813AP/

APT

NE5532

OUT

OW18

Figure 10. Complete 8

18-Bit CD Player

AD1865

REV. 0

MULTICHANNEL DIGITAL KEYBOARD DESIGN

Figure 11 illustrates how to cascade AD1865's to add multiple
voices to an electronic musical instrument. In this example, the
data and clock signals are shared between all six DACs. As the
data representing an output for a specific voice is loaded, the ap-
propriate DAC is updated. For example, after the 18-bits repre-
senting the next output value for Voice 4 is clocked out on the
data line, then "Voice 4 Load" is pulled low. This produces a
new output for Voice 4. Furthermore, all voices can be returned
to the same output by pulling all six load signals low.

In this application, the advantages of choosing the AD1865 are
clear. Its flexible digital interface allows the clock and data to be
shared among all DACs. This reduces PC board area require-
ments and also simplifies the actual layout of the board. The low
power requirements of the AD1865 (approximately 225 mW) is
an advantage in a multiple DAC system where any power advan-
tage is multiplied by the number of DACs used. The AD1865
requires no external components, simplifying the design, reduc-
ing the total number of components required and enhancing
reliability.

AD1865

TRIM

MSB

AGND

OUT

CLK

+5V ANALOG

SUPPLY

5V ANALOG

SUPPLY

VOICE 1

OUTPUT

AD1865

VOICE 1 LOAD

ANALOG

COMMON

VOICE 3 LOAD

DATA

VOICE 2 LOAD

CLOCK

VOICE 2

OUTPUT

VOICE 3

OUTPUT

VOICE 4

OUTPUT

VOICE 5

OUTPUT

VOICE 6

OUTPUT

VOICE 6 LOAD

VOICE 5 LOAD

VOICE 4 LOAD

DIGITAL COMMON

+5V DIGITAL SUPPLY

DGND

OUT

TRIM

MSB

AGND

TRIM

MSB

AGND

OUT

CLK

TRIM

MSB

AGND

OUT

CLK

DGND

OUT

TRIM

MSB

AGND

DGND

OUT

TRIM

MSB

AGND

Figure 11. Cascaded AD1865s in a Multichannel Keyboard Instrument

AD1865

REV. 0

ADDITIONAL APPLICATIONS

Figures 12 through 14 show connection diagrams for the AD1865
and standard digital filter chips from Yamaha, NPC and Sony.
Each figure is an example of cophase operation operating at 8

for each channel. The 2-pole Rauch low-pass filters shown in

Figure 10 can be used with all of the applications shown in this
data sheet.

AD1865

MSB

OUT

DGND

OUT

TRIM

MSB

AGND

TRIM

AGND

OUT

CLK

+5V DIGITAL SUPPLY

LPF

RIGHT
CHANNEL
OUTPUT

LEFT
CHANNEL
OUTPUT

5V ANALOG

SUPPLY

+5V ANALOG

SUPPLY

SHL

DD2

SHR

BCO

WCO

DLO

DD1

DRO

YM3434

16/18

Figure 12. AD1865 with Yamaha YM3434 Digital Filter

AD1865

MSB

OUT

DGND

OUT

TRIM

MSB

AGND

TRIM

AGND

OUT

CLK

+5V DIGITAL SUPPLY

LPF

RIGHT
CHANNEL
OUTPUT

LEFT
CHANNEL
OUTPUT

5V ANALOG

SUPPLY

+5V ANALOG

SUPPLY

LPF

DOL

DOR

WDCO

BCKO

SM5818

OMOD1

OMOD2

Figure 14. AD1865 with NPC SM5818AP Digital Filter

AD1865

MSB

OUT

DGND

OUT

TRIM

MSB

AGND

TRIM

AGND

OUT

CLK

LPF

RIGHT
CHANNEL
OUTPUT

LEFT
CHANNEL
OUTPUT

5V ANALOG

SUPPLY

+5V ANALOG

SUPPLY

16.9344

MHz

GND

TEST

XIN

LFS

SONY/12S

TEST

DPOL

OUT 16/18

LE/WS

DATAR

GND

DATAL

BCKO

CXD1244S

LPF

+5V DIGITAL SUPPLY

Figure 13. AD1865 with Sony CXD1244s Digital Filter

AD1865

REV. 0

OTHER DIGITAL AUDIO COMPONENTS AVAILABLE

FROM ANALOG DEVICES

AD1856

DGND

CLK

DATA

NC NO CONNECT

TRIM

MSB ADJ

OUT

AGND

OUT

16-BIT

LATCH

SERIAL

INPUT

REGISTER

16-BIT

DAC

OUT

CONTROL

LOGIC

REF

AD1860

DGND

CLK

DATA

NC NO CONNECT

TRIM

MSB ADJ

OUT

AGND

OUT

18-BIT

LATCH

SERIAL

INPUT

REGISTER

18-BIT

DAC

OUT

CONTROL

LOGIC

REF

AD1862

CLK

DATA

TRIM

ADJ

AGND

OUT

DGND

VOLTAGE

REFERENCE

INPUT

DIGITAL
OFFSET

20-BIT

DAC

AD1856 16-BIT AUDIO DAC

Complete, No External Components Required
0.0025% THD
Low Cost
16-Pin DIP or SOIC Package
Standard Pinout

AD1860 18-BIT AUDIO DAC

Complete, No External Components Required
0.0025% THD+N
108 dB Signal-to-Noise Ratio
16-Pin DIP or SOIC Package
Standard Pinout

AD1862 20-BIT AUDIO DAC

119 dB Signal-to-Noise Ratio
0.0016% THD+N
102 dB D-Range Performance

1 dB Gain Linearity

16-Pin DIP Package

AD1868 +5 V SINGLE SUPPLY DUAL 18-BIT
AUDIO DAC

No External Components Required
0.004% THD+N
92 dB D-Range Performance

3 dB Gain Linearity

16-Pin DIP or SOIC Package

18-BIT

DAC

18-BIT

SERIAL

REGISTER

AD1868

CLK

DGND

BIAS

OUT

NRL

AGND

NRR

OUT

18-BIT

DAC

18-BIT

SERIAL

REGISTER

REF

Ð­Ð»ÐµÐºÑ‚Ñ€Ð¾Ð½Ð½Ñ‹Ð¹ ÐºÐ¾Ð¼Ð¿Ð¾Ð½ÐµÐ½Ñ‚: AD1865

ÐÐ»ÐµÐºÑ‚Ñ€Ð¾Ð½Ð½Ñ‹Ð¹ ÐºÐ¾Ð¼Ð¿Ð¾Ð½ÐµÐ½Ñ‚: AD1865